Hitachi NT 65A3 Скачать руководство пользователя

Страница: 6 / 45

--- 3 ---

(Valve sleeve (A))

5-3. Explanation of the Nailing Operation

To meet the requirements of "ANSI SNT-101-2002", the Model NT 65A3 is equipped with a nailing operation

switching device at the valve portion as shown in the figures below. Use SINGLE ACTUATION MECHANISM

(SINGLE SEQUENTIAL ACTUATION MECHANISM) or CONTACT ACTUATION MECHANISM in accordance with

the work to be performed. A FULL SEQUENTIAL ACTUATION MECHANISM KIT (SEQUENTIAL TRIP

MECHANISM KIT) is also available as an option. Each nailing operation is as follows.

SINGLE ACTUATION MECHANISM (SINGLE SEQUENTIAL ACTUATION MECHANISM):

First, press the pushing lever against the wood; next, pull the trigger to drive the nail. First, pull the trigger; next,

press the pushing lever against the wood to drive the nail. After nailing once, nailing will not be possible again

until the trigger is released and pressed again.

CONTACT ACTUATION MECHANISM:

First, press the pushing lever against the wood; next, pull the trigger to drive the nail. First, pull the trigger; next,

press the pushing lever against the wood to drive the nail. If the trigger is held back, a nail will be driven each

time the pushing lever is pressed against the wood.

FULL SEQUENTIAL ACTUATION MECHANISM:

First, press the pushing lever against the wood; next, pull the trigger to drive the nail. Follow the same sequence

to continue driving nails.

Содержание NT 65A3














































Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды

Hitachi NT 65A3, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды