English
13
WARNING
If the cutting attachment still rotates after adjustment of
the idle speed adjustment screw (T), immediately stop
the engine and cease use, then contact the nearest
Hitachi Authorized Service Center.
Air
fi
lter (Fig. 31)
The air
fi
lter (29) must be cleaned from dust and dirt in order
to avoid:
○
Carburetor malfunctions.
○
Starting problems.
○
Engine power reduction.
○
Unnecessary wear on the engine parts.
○
Abnormal fuel consumption.
Clean the air
fi
lter daily or more often if working in
exceptionally dusty areas.
Open the air
fi
lter cover and remove the air
fi
lter (29). Clean it.
Check that the
fi
lter is dry before reassembly.
An air
fi
lter that has been used for some time cannot be
cleaned completely. Therefore, it must regularly be replaced
with a new one. A damaged
fi
lter must always be replaced.
NOTE
To put the air
fi
lter cover back into place, hook it on the
upper tabs and then attach it.
Fuel
fi
lter (Fig. 32)
Remove the fuel
fi
lter (30) from the fuel tank, and replace it if
it is dirty.
NOTE
A blocked fuel
fi
lter (30) can prevent the supply of fuel and
cause a rotation malfunction of the engine.
Spark plug (Fig. 33)
The spark plug condition is in
fl
uenced by:
○
An incorrect carburetor setting.
○
Wrong fuel mixture (too much oil in the gasoline)
○
A dirty air
fi
lter.
○
Hard running conditions (such as cold weather).
These factors cause deposits on the spark plug electrodes,
which may result in malfunction and starting di
ffi
culties. If
the engine is low on power, di
ffi
cult to start or runs poorly at
idling speed, always check the spark plug
fi
rst.
If the spark plug is dirty, clean it and check the electrode
gap. Re-adjust if necessary. The correct gap is 0.6 mm. The
spark plug should be replaced after about 100 operation
hours or earlier if the electrodes are badly eroded.
NOTE
In some areas, local law requires using a resistor spark
plug to suppress ignition signals. If this machine was
originally equipped with resistor spark plug, use same
type of spark plug for replacement.
Flexible drive shaft (Fig. 34)
(CG23ECP (LB))
Flexible drive shaft should be removed and lubricated with
good quality lithium grease every 20 hours. To remove the
fl
exible shaft,
fi
rst remove screw (31), loosen bolt (32) and
remove the cutter case then pull the shaft out of the drive
shaft tube. Clean the shaft o
ff
and apply a generous coat of
lithium grease to it and insert if back into the drive shaft tube,
turn it unit it drops into place then install the cutter case,
install & tighten screw (31) and bolt (32).
Gear case (Fig. 35)
Check gear case or angle gear for grease level about every
50 hours of operation by removing the grease
fi
ller plug on
the side of gear case.
If no grease can be seen on the
fl
anks of the gears,
fi
ll the
gear case with quality lithium based multipurpose grease up
to 3/4. Do not completely
fi
ll the gear case.
CAUTION
○
Make sure to remove any dirt or grit when attaching the
plug to its original position.
○
Before attempting inspection or maintenance of the gear
case, make sure the case has cooled.
Semi-auto cutting head
Nylon line replacement
1. Remove the case (17) by
fi
rmly pushing inward the
locking tabs with your thumbs as shown in
Fig. 36
.
2. After removing the case, take out the reel and discard
the remaining line.
3. Fold the new nylon line unevenly (approx. 10 cm) in half
as shown in picture.
Hook the U-shaped end of the nylon line into the groove
(33) on the center partition of the reel.
Wind both halves of the line on the reel in the same
direction, keeping each half of the line on its own side of
the partition. (
Fig. 37
)
4. Push each line into the stopper holes (34), leaving the
loose ends approx. 10 cm in length. (
Fig. 38
)
5. Insert both loose ends of the line through the cord guide
(35) when placing the reel in the case. (
Fig. 39
)
NOTE
When placing a reel in the case, try to line up the stopper
holes (34) with the cord guide (35) for easier line release
later.
6. Place the cover over the case so that the cap locking
tabs (37) on the cover meet the long holes (36) on the
case. Then push the case securely until it clicks into
place. (
Fig. 40
)
7. The initial cutting line length should be approx. 11–14 cm
and should be equal on both sides. (
Fig. 41
)
Blade (Fig. 42)
WARNING
Wear protective gloves when handling or performing
maintenance on the blade.
○
Use a sharp blade. A dull blade is more likely to snag and
thrust.
Replace the fastening nut if it is damaged and hard to
tighten.
○
When replacing blade, purchase one recommended by
Hitachi, with a 25.4 mm (one inch)
fi
tting hole.
○
In the case of a 3 tooth blade (38), it can be used on
either side.
○
Use the correct blade for the type of work.
○
When replacing blades, use appropriate tools.
○
When cutting edges become dull, re-sharpen or
fi
le
as shown in the illustration. Incorrect sharpening may
cause excessive vibration.
○
Discard blades that are bent, warped, cracked, broken
or damaged in any way.
NOTE
When sharpening blade it is important to maintain an
original shape of radius at the base of the tooth to avoid
cracking.
For long-term storage
Drain all fuel from the fuel tank. Start and let engine run until
it stops. Repair any damage which has resulted from use.
Clean the unit with a clean rag, or the use of high pressure
air hose. Put a few drops of two-cycle engine oil into the
cylinder through the spark plug hole, and spin the engine
over several times to distribute oil.
Cover the unit and store it in a dry area.
Maintenance schedule
Below you will
fi
nd some general maintenance instructions.
For further information please contact Hitachi Authorized
Service Centers.
000Book̲CG23ECP(SL).indb 13
000Book̲CG23ECP(SL).indb 13
2016/05/16 10:34:12
2016/05/16 10:34:12
