24
en
9. Troubleshooting
Symptom
Possible cause
Possible solution
The tool doesn’t start
Fault in the electric power supply
Plug in another electric tool and
check whether it starts.
Defective supply cord or plug
Have it checked by an electric
specialist and replace if necessary.
Switch defective
Have it checked by an electric
specialist and replace if necessary.
Tool doesn’t produce full
Cross-section of the
Use an extension cord of adequate
power
extension cord is inadequate
cross-sectional.
See section «Preparation for use»
Speed preselection thumbwheel
Set the speed preselection thumbweel
ist not set to position 6
to position 6.
Blade clamping nut cannot
Lever not moved the full distance
With the blade clamping lever opened
be released
when the blade was changed
as far as it will go, use a suitable
previously, or contrary to
wrench to release the clamping nut.
instructions, a tool was used to
The clamping nut should be tightened
tighten the clamping nut
by hand only.
No / reduced suction power
Chip ejector channel blocked
Clean out the chip ejector channel.
Additional claims are excluded, unless stringent
national rules prohibit such exclusion. In particular,
Hilti is not obligated for direct, indirect, incidental
or consequential damages, losses or expenses in
connection with, or by reason of, the use of, or inabil-
ity to use the tool for any purpose. Implied warranties
of merchantability or fitness for a particular purpose
are specifically excluded.
For repair or replacement, send tool or related parts
immediately upon discovery of the defect to the address
of the local Hilti marketing organization provided.
This constitutes Hilti's entire obligation with regard to
warranty and supersedes all prior or contemporane-
ous comments and oral or written agreements con-
cerning warranties.
10. Disposal
Most of the materials from which Hilti power tools
are manufactured can be recycled. The materials
must be correctly separated before they can be
recycled. In many countries, Hilti has already made arrange-
ments for taking back your old electric tools for recycling.
Please ask your Hilti customer service department or Hilti
sales representative for further information.
Only for EU countries
Disposal of electric tools together with house-
hold waste is not permissible!
In observance of European Directive 2002/96/EC on waste
electrical and electronic equipment and its implementation
in accordance with national law, electric tools that have
reached the end of their life must be collected separately
and returned to an environmentally compatible recycling
facility.
11. Manufacturer’s warranty – tools
Hilti warrants that the tool supplied is free of defects
in material and workmanship. This warranty is valid so
long as the tool is operated and handled correctly,
cleaned and serviced properly and in accordance with
the Hilti Operating Instructions, and the technical sys-
tem is maintained. This means that only original Hilti
consumables, components and spare parts may be
used in the tool.
This warranty provides the free-of-charge repair or
replacement of defective parts only over the entire lifes-
pan of the tool. Parts requiring repair or replacement
as a result of normal wear and tear are not covered by
this warranty.
12. EC declaration of conformity
Description:
Circular saw
Designation:
WSC255-KE/WSC265-KE
Year of design:
2000
We declare, under our sole responsibility, that this prod-
uct complies with the following directives and standards:
2004/108/CE, as of 28.12.2009 98/37/EC, as of 29.12.2009
2006/42/EC, EN 55 014-1, EN 55 014-2, EN 60 745-1,
EN 60745-2-5, EN 61000-3-2, EN 61000-3-3
Hilti Corporation
Peter Cavada
Dr. Heinz-Joachim Schneider
Head Process & Quality Management
Executive Vice President
Business Area
Business Area
Electric Tools & Accessories
Electric Tools & Accessories
02/2006
02/2006
Printed: 07.07.2013 | Doc-Nr: PUB / 5071325 / 000 / 00
