HIKOKI G 23BYE, Инструкция по эксплуатации, Страница: 8 / 28

8
English
SPECIFICATIONS
Model G23BYE
Voltage (by areas)*
1
(230 V)
Power Input*
1
2200 W
Rated speed
6600 min -1
Wheel
Outer dia. 230 mm
Hole Dia.
22.23 mm
Thickness
6 mm
Peripheral speed
80 m/s
Weight* 2
4.2 kg
*1 Be sure to check the nameplate on product as it is subject
to change by areas.
*2 Weight: According to EPTA-Procedure 01/2003
Electronic control
○ Soft start
Reduces recoil against the operator by managing the
number of rotations during startup.
○ 0 Voltage Re-start Protection
The 0 voltage restart protection feature prevents the
power tool from restarting after the power has been
temporarily cut o ff during operation.
○ Constant speed
○ Overload protection
This protection feature cuts o ff the power to the motor
in the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been
activated, the motor may stop.
In this case, release the tool switch and eliminate causes
of overloading.
After that you can use it again.
○ Overheat protection
This protection feature cuts o ff the power to the motor
and stops the power tool in the event of overheating of
motor during operation.
When the overheat protection feature has been
activated, the motor may stop.
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
○ Brake function
Brake activates when the trigger is o ff .
NOTE
○ To prevent the tip tool from falling o ff , the brake will not
be applied when the switch is released right after startup
(within one second).
○ Due to HiKOKI’s continuing program of research and
development, the speci fi cations herein are subject to
change without prior notice.
NOTIFICATION LAMP
This product features a noti fi cation lamp.
Listed below are the situations that trigger each of the lamp
noti fi cations.
Noti fi cation
Lamp Display
Situation
Lights green Power plug is connected to an
outlet and the unit is on standby for
operation.
Switch the unit ON to begin operation.
Lights red
Indicates the activation of a safety
system feature that prevents sudden
activation when the power returns after
being interrupted from causes such
as power plug disconnection or power
outage during continuous operation.
To cancel the feature, switch the unit
OFF once.
[Restart protection function]
Blinks red
Operation stopped due to overload.
Continue operation after removing the
cause of the overload.
[Overload protection function]
Operation stopped due to overheating.
Disconnect the power plug from the
outlet and allow the unit to cool in a
well-ventilated, shaded area.
The unit can be used once it has
cooled down.
[Overheat protection function]
Operation stopped due to pulling the
switch while the brake was being
applied after releasing the switch.
The unit can be operated once the
revolution has stopped and the switch
is pulled once again.
MOUNTING AND OPERATION
Action Figure Page
Fitting and adjusting the wheel
guard
2 2
Fixing the side handle 3 2
Assembling depressed center
wheel
4 2
Assembling cutting wheel*
1
5 2
Assembling diamond wheel 6 3
Switch operation 7 3
Grinding angle and grinding
method
8 3
Detaching the fi lter 9 3
Selecting accessories ― 25
*1 WARNING
Before use, be sure to tighten the wheel nut with the
included wrench.
Failure to tighten could result in the wheel nut
loosening when the brake is activated during a stop.
0000Book̲G23BYE̲Ukr̲Rus.indb 8 0000Book̲G23BYE̲Ukr̲Rus.indb 8 2018/11/16 14:00:34 2018/11/16 14:00:34