7
English
5. Con
fi
rm that the push button is disengaged by pushing
push button two or three times before switching the
power tool on.
6. To prolong the life of the machine and ensure a
fi
rst
class
fi
nish, it is important that the machine should not
be overloaded by applying too much pressure. In most
applications, the weight of the machine alone is su
ffi
cient
for e
ff
ective grinding. Too much pressure will result in
reduced rotational speed, inferior surface
fi
nish, and
overloading which could reduce the life of the machine.
7. The wheel continues to rotate after the tool is switched
o
ff
.
After switching o
ff
the machine, do not put it down until
the depressed center wheel has come to a complete
stop. Apart from avoiding serious accidents, this
precaution will reduce the amount of dust and swarf
sucked into the machine.
8. When the machine is not use, the power source should
be disconnected.
9. Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident
before the depressed center wheel is assembling and
disassembling.
10. Caution when using near welding equipment
When using the grinder in the immediate vicinity of
welding equipment, the rotational speed may become
unstable. Do not use the grinder near welding equipment.
11. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
12. Be careful of brake kickback.
This disk grinder features an electric brake that functions
when the switch is released. As there is some kickback
when the brake functions, be sure to hold the main body
securely.
NAMES OF PARTS (Fig. 1 – Fig. 9)
ⓐ
Push button
ⓙ
Lock lever
ⓑ
Side handle
ⓚ
Tail cover
ⓒ
Gear cover
ⓛ
Housing
ⓓ
M5 bolt
ⓜ
Filter
ⓔ
Depressed center
wheel
ⓝ
Wrench
ⓕ
Wheel washer
ⓞ
Wheel nut
ⓖ
Wheel guard
ⓟ
Cutting wheel
ⓗ
Lever
ⓠ
With base foot
ⓘ
Switch
ⓡ
Diamond wheel
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
G23BYE: Disc Grinder
To reduce the risk of injury, user must read
instruction manual.
Always wear eye protection.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V
Rated voltage
Alternating current
n
Rated speed
min
-1
Revolution or reciprocations per minute
Switching ON
Switching OFF
Lock
Switch locks to the “ON” position.
Soft start
Disconnect mains plug from electrical outlet
Warning
Class
II
tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○
Wrench .........................................................................1
○
Side handle
...................................................................1
○
Depressed center wheel ...............................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○
Removal of casting
fi
n and
fi
nishing of various types of
steel, bronze and aluminum materials and castings.
○
Grinding of welded sections or sections cut by means of
a cutting torch.
○
Grinding of synthetic resins, slate, brick, marble, etc.
○
Cutting of synthetic concrete, stone, brick, marble, and
similar materials.
0000Book̲G23BYE̲Ukr̲Rus.indb 7
0000Book̲G23BYE̲Ukr̲Rus.indb 7
2018/11/16 14:00:34
2018/11/16 14:00:34