HIAB K-HiPro 285-425-4 Series Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 114

background image

Viscosity of oil at 40°C

Temperature range

32

-25°C to 75°C

46

-15°C to 90°C

68

-5°C to 90°C

The recommended viscosity during normal working conditions is between 16 and 40cSt.
HIAB strongly recommend an oil working temperature below 70°C. If necessary consider an oil

cooler or heater.

NOTE

When working in artic condition consider an oil with lower viscosity than the 32 oil

in the table above.

Environmentally Friendly Oil

The environmentally friendly oils recommended for HIAB products are ester based synthetic

hydraulic fluids (synthetic ester).

NOTE

Vegetable oils do not meet HIAB’s requirements and must not be used.

After filling the tank
1. Operate each crane function to its end positions.
2. Operate the crane to parking position.
3. Check and top up the oil tank to max level on the tank gauge.
4. Bleed the system.

8.5.4. Bleeding air from the hydraulic system

Bleed the air from the hydraulic system:
• after changing the hydraulic oil
• after working on the hydraulic system
• if your crane works slowly or jerkily
• if your crane has not been used for a long time

WARNING

Air in the hydraulic system can lead to faults and damage

To bleed air from the hydraulic system, proceed as follows:
Move each crane cylinder and each hydraulically operated piece of add-on equipment at least

twice to its end positions (slowly).

Maintenance and Service

HIAB K-HiPro 285-425 X4

99

«
...
97
98
99
100
101
...
»

Содержание K-HiPro 285-425-4 Series



















































































































Отзывы:

Нет отзывов

Похожие инструкции для K-HiPro 285-425-4 Series

Бренд: Tate Страницы: 7

Бренд: Tate Страницы: 5

BioHarmonex BH4

Бренд: Calivita Страницы: 38

Бренд: CAIRE Страницы: 91

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: ParaBody Страницы: 5

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренд: Valcom Страницы: 6

Бренд: Vaisala Страницы: 60

bionic power knee

Бренд: Össur Страницы: 2

BALANCE KNEE OM8

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 37

REBOUND DIABETIC WALKER

Бренд: Össur Страницы: 63

Бренд: Össur Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды