HIAB K-HiPro 285-425-4 Series Скачать руководство пользователя страница 96

Страница: 96 / 114

8.5. Hydraulics

8.5.1. Slewing housing: checking the oil level/oil change

Measuring stick [if fitted]

• Checking the oil level in slewing housing

1. Check if the oil level on the measuring stick is

between the maximum and minimum levels.

2. If the oil level is below the minimum level: Top up

through the hole for the measuring stick with

transmission oil of type MIL-L-2105C or API-GL-5,

viscosity SAE-80W-90, cleanliness NAS 1638:8.

• Changing oil in the slewing housing

Change the oil in the slewing house yearly!
1. Use a container with sufficient capacity to receive

the oil. Drain off the oil through the drain plug.

2. Refill through the hole for the measuring stick,

with transmission oil of type MIL-L-2105C or API-

GL-5, viscosity SAE-80W-90, cleanliness NAS

1638:8.

3. Slew the crane to the end positions three times.
4. Check the oil level. If necessary top up again.

Measuring level glass [if fitted]

• Checking the oil level in slewing housing

1. Check if the oil level in the level glass (1) is

between the maximum and minimum levels.

2. If the oil level is below the minimum level: Remove

the plug (3).

3. Top up through the filling hole (3) with

transmission oil of type MIL-L-2105C or API-GL-5,

viscosity SAE-80W-90, cleanliness NAS 1638:8.

• Changing oil in the slewing housing

Change the oil in the slewing house yearly!
1. Remove the hose coupling (2) from the level

glass.

2. Remove the plug (3).
3. Use a container with sufficient capacity to receive

the oil. Drain off the oil through the filling hose (2).

4. Attach the hose coupling (2) to the level glass.
5. Refill through the filling hole (3), with transmission oil of type MIL-L-2105C or API-GL-5,

viscosity SAE-80W-90, cleanliness NAS 1638:8.

➂

➁

➀

Maintenance and Service

HIAB K-HiPro 285-425 X4

Содержание K-HiPro 285-425-4 Series



















































































































Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды

HIAB K-HiPro 285-425-4 Series, Руководство оператора

Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды