HIAB K-HiPro 285-425-4 Series Скачать руководство пользователя страница 106

Страница: 106 / 114

Fault

Probable cause

Action

Leak on hydraulic system: leaking

coupling, hose or line. Danger! Keep

away from any oil leak.

1. Push in the Stop

button [If fitted].
2. Disengage the PTO.
3. Contact a HIAB

service workshop.

Stabiliser extensions do not slide out.

Stabiliser extensions

are still locked.

Unlock the stabiliser

extensions.

Hydraulic fault.

Go to a HIAB service

workshop.

The stabiliser extensions do not slide

out/in. (Chain-driven stabiliser

system)

Incorrect chain

tension.

Contact a HIAB service

workshop.

The stabiliser leg cylinder cannot

keep the truck load and it goes

inwards.

Check valve

damaged.

Go to a HIAB service

workshop.

Cylinder internal

leakage.

Go to a HIAB service

workshop.

Soft ground surface.

Set again the stabiliser

led onto the ground or

add an extra support

plate between the

cylinder and ground.

Slewing support cylinders do not turn

Three-way valve

failure.

Go to a HIAB service

workshop.

Irregular slewing movements and

unusual noises in cranes with rack

and pinion slewing system.

Insufficient oil in the

hydraulic system.

Top up the oil tank.

Insufficient oil in the

slewing housing.

Top up the oil in the

slewing housing to the

required level.

The upper slewing

bearing is not

properly lubricated.

Lubricate the bearing.

The bearings in the

slewing housing are

damaged.

Go to a HIAB service

workshop.

Irregular slewing movements and

unusual noises in cranes with

continuous slewing system.

Insufficient oil in the

hydraulic system.

Top up the oil tank.

Insufficient oil in the

gear box.

Top up the oil in the gear

box to the required level.

Bearing assemblies

and pinion are not

properly lubricated.

Lubricate the bearing

while slewing.

Maintenance and Service

106

HIAB K-HiPro 285-425 X4

Содержание K-HiPro 285-425-4 Series



















































































































Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды

HIAB K-HiPro 285-425-4 Series, Руководство оператора

Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды