HIAB K-HiPro 285-425-4 Series Скачать руководство пользователя страница 31

Страница: 31 / 114

WARNING

• Never push a load along the ground, or

the vehicle's load space, with the

extension boom. This can cause damage

to the boom system. This will lead to

expensive repairs.

• Never use the extension boom as a jack.

This could damage the slewing bearings

and the connection between the crane

column and the crane base.

• Always lift the load from the ground before

you start to slew. Do not tow the load over

the ground. This can damage the boom

system.

• If you are working with loads in restricted

spaces (for example, windows):
Check that the boom system can move up

and down freely.
The boom system will bend somewhat,

when loading and unloading the crane.

• If the boom system is in a high position

(first boom above 70°), do not allow the

boom to lower at full speed. The crane

could go into an uncontrolled movement.
Be careful if, in particular, the OLP gives

an early warning!

• When loading the vehicle:

Take the load off the stabiliser legs by

withdrawing them slightly. The stabiliser

legs must remain in light contact with the

ground.

CAUTION

• Operate the crane using smooth and gentle lever movements.
• If a cylinder is at its end position, free the operating lever. Otherwise overheating

can occur.

Safety precautions and warnings

HIAB K-HiPro 285-425 X4

Содержание K-HiPro 285-425-4 Series



















































































































Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды

HIAB K-HiPro 285-425-4 Series, Руководство оператора

Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды