HIAB K-HiPro 285-425-4 Series Скачать руководство пользователя страница 48

Страница: 48 / 114

CTC symbols

The order of the levers is customized.
• CTC mode, crane tip up/down ①
• CTC mode, crane tip out/in ②
• Activate manual control of the 1st boom in CTC mode ③
• Operate 1st boom up/down manually in CTC mode ④

4.12.5. Battery and battery charger XSDrive

Battery

A fully charged battery provides approximately 5-8 hours use (at 25 °C, 77 °F) and the voltage level

is approximately 8,4V. When the battery is about to wear out an indicator LED on the controller

burns steady red and the horn will sound twice. Push the stop button before changing the battery.

Note that the battery voltage remains between 7,6V and 7,5V for a long time. Therefore, the battery

voltage cannot be used to estimate remaining hours of use.

Battery charger

The battery charger is to be fitted in a protected

environment, preferably in the cab. Two batteries are

delivered with each unit, one of which can always be

placed in the charger.
LED (1) is lit continuously when the battery charger is

ready for use. Place the battery in the charger. LED (2)

flashes slowly during recharging and has a steady light

when the battery is fully charged.

Charging time

The normal charging time for a flat battery, is approximately 3 hours. Operating ambient temp:

Battery = 0° to + 45°C.

NOTE

A charged battery is a concentrated energy source. Never store a charged battery

in a toolbox or similar, where there is a risk of a short due to contact with metal

components. Used batteries should be taken care of according to the local

regulations.

The HiPro system

HIAB K-HiPro 285-425 X4

Содержание K-HiPro 285-425-4 Series



















































































































Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды

HIAB K-HiPro 285-425-4 Series, Руководство оператора

Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды