HIAB K-HiPro 285-425-4 Series Скачать руководство пользователя страница 95

Страница: 95 / 114

8.4.2. Lubrication of the upper column bearing

DANGER

The upper column bearing must be lubricated while the crane is slewed. If one

person lubricates the upper column bearing, while another is slewing the crane:

Take care that the person lubricating the bearing does not come into contact or get

crushed by the crane!

If you are lubricating the upper column bearing without

help:
• Lubricate the upper bearing with a little grease.
• Slew the crane a little.
• Again lubricate with a little grease. Repeat, until the

column has been slewed round completely.

8.4.3. Lubrication of slide pads in boom system

Front upper slide pads
• Extend extensions with load in order to create enough clearance.
• Lubricate.
Front lower slide pads
• Extend extensions without load and push slightly against the ground in order to create enough

clearance.

• Lubricate.

8.4.4. Lubrication of the hooks

• Hooks with plane bearing.

If the hook cannot rotate easily without load:
1. Lubricate the plane bearing surfaces (1).

Use a heavy duty penetrating spray grease, type

"ZEP 2000" or equivalent quality.

• Hooks with swivel.

Lubricate if the swivel cannot rotate easily:
1. Remove the screw (2) and mount a grease nipple.
2. Add grease until grease appears between house (3)

and shank (4).

3. Mount the screw (2).

Use a bearing grease, type "Texaco Multifak EP 2" or equivalent quality.

Maintenance and Service

HIAB K-HiPro 285-425 X4

Содержание K-HiPro 285-425-4 Series



















































































































Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды

HIAB K-HiPro 285-425-4 Series, Руководство оператора

Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды