Herz pelletstar CONDENSATION 10 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 94

background image

T-CONTROL

9

25

9.6

Switching the boiler on and off (Chimney sweeping function)

SWITCH-ON

SWITCH-OFF

Navigation:

Navigation:

Screen:

Screen:

By pressing the button:

By pressing the button:

the boiler will be switched on.

the boiler will be switched off.

the boiler will switch off, remains
off and the previous page will be
displayed.

the boiler remains on and the
previous page will be displayed.

Note:

Note:

The system can only be switched on if there are no
errors that prevent it from starting.

The boiler will switch to

the operating condition “burn

out  phase”  (except  “cold  start”  or  “ready”).  When
switching off during cold start, the cold start is ended
and  then  changes  to  the  burnout  phase.  This
prevents  impermissibly  high  amount  of  fuel  in  the
combustion chamber.

CHIMNEY SWEEPING FUNCTION

Navigation:

Screen:

If “chimney sweeping function” is
active, the remaining time can be
raised in 5 minutes steps by
pushing the

-button.

Raises

the

remaining

time

(chimney sweeping mode) by
5 minutes steps.

After pressing the chimney sweeping symbol, the
boiler can also be switched off.

«
...
23
24
25
26
27
...
»

Содержание pelletstar CONDENSATION 10































































































Отзывы:

Нет отзывов

Похожие инструкции для pelletstar CONDENSATION 10

Бренд: Laars Страницы: 9

Бренд: U.S. Boiler Company Страницы: 8

Бренд: U.S. Boiler Company Страницы: 60

Бренд: U.S. Boiler Company Страницы: 100

Бренд: U.S. Boiler Company Страницы: 56

Бренд: U.S. Boiler Company Страницы: 60

InTec 12S (LPG)

Бренд: Alpha Страницы: 44

ecoFIT sustain 800 Series

Бренд: Vaillant Страницы: 56

EXALT Combi 155

Бренд: IDEAL Страницы: 39

Бренд: REMEHA Страницы: 60

ecoBLOCK exclusiv VM IT 466/4-7

Бренд: Vaillant Страницы: 68

Бренд: IBC Страницы: 4

Бренд: Biasi Страницы: 44

Бренд: Alarko Страницы: 60

Бренд: Super Hot Страницы: 14

Henrad WH LX 30 FF

Бренд: IDEAL Страницы: 40

Бренд: Teba therm Страницы: 21

Proteus Plus Blue 24 kW

Бренд: E.C.A. Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды