background image

Warning notes 

2

 

 

 

WARNING NOTES 

 

Risk  of  injury  and  damage  to 
property 

due 

to 

improper 

handling  of  the  system.  Damage 
to property is possible. 

 

Caution 

– hot surface 

 

Warning 

– against hand injuries. 

 

No 

admittance 

without 

authorisation. 

 

However, 

adherence 

to 

guidelines 

for 

transportation, 

installation, 

operation 

and 

maintenance  notices  as  well  as  technical  data (in 
the  operating  instructions,  product  documentation 
and  on  the  equipment  itself)  which  are  not 
specifically  highlighted,  is  also  vital  to  avoid 
breakdowns which may directly or indirectly cause 
major personal or material damage. 

General safety notes 

For  reasons  of  clarity  and  possible  permutations, 
this  documentation  does  not  contain  all  detailed 
information  and  cannot  take  account  of  every 
conceivable  operating  or  maintenance  scenario. 
Should  you  require  further  information  or 
encounter  specific  problems,  which  are  not 
handled  in  detail  in  the  documentation  supplied, 
you can obtain the required information from your 
specialist dealer or direct from HERZ.  

People  (including  children)  who,  because  of  their 
physical,  sensory  or  mental  capabilities  or 
because of their lack of experience or knowledge, 
are  unable  to  use  the  equipment  safely  must  not 
use this equipment unless  they are supervised  or 
instructed by a responsible person. 

Basic safety information 

Due  to  its  functionally  limited  electrical  and 
mechanical  characteristics  with  regard  to  usage, 
operation  and  maintenance,  if  the  equipment  is 
not  able  to  work  according  to  its  appropriate  use 
or  improper  interference  occurs,  it  may  cause 
serious health and material damage. It is therefore 
conditional  that  the  planning  and  implementation 
of  all  installations,  transportation,  operation  and 
maintenance will be carried out and supervised by 
responsible, qualified persons. 

 

When  operating  electrical  systems,  certain  parts 
of  those  systems  will  always  carry  a  hazardous 
electrical  voltage  or  be  exposed  to  a  mechanical 
load.  Only  appropriately  qualified  personnel  may 
carry  out  work  on  the  system.  They  must  be 
thoroughly familiar  with the content of this  and all 
other manuals. In order for this system to function 
safely  and  without  any  problems,  transportation, 
storage,  operation  and  maintenance  must  be 
carried out properly and carefully. Instructions and 
information on the systems must also be heeded. 

2.1 

Installation 

General safety notes 

In  order  to  ensure  that  the  system  will  function 
properly, 

the  relevant 

standards 

and 

the 

manufacturer’s  installation  instructions  are  to  be 
heeded during the installation of the system! 

Documents  from  the  manufacturer  relating  to  the 
heating  devices  and  components  used  are 
available from HERZ on request. 

2.2 

Operation and maintenance 

2.2.1 

General safety notes 

 

In  order  for  the  system  to  be 
operated and maintained safely, it 
must be operated and maintained 
properly  by  qualified  personnel 
while heeding the warnings in this 
documentation 

and 

the 

instructions on the systems. 

 

In 

unfavourable 

operating 

conditions,  the  temperatures  of 
parts  of  the  housing  may  exceed 
80 °C. 

 

Ambient conditions 

Operating temperature: 

+10 to +40 °C 

Warehouse-/ transport 
temperature: 

-20 to +70 °C 

Humidity: 

operation 

5 to 85 % 

 

storage 

5 to 95 % 

 

 

 

Содержание firestar de Luxe 18



























































































Отзывы: