Herz firestar de Luxe 18 страница 59 Скачать руководство пользователя

Страница: 59 / 90

Boiler control

9.14.5

Information overview

Navigation:

Screen:

Note:

The information shows an overview of the current software versions, operating system, firmware and also the
hydraulic scheme. If a USB-Stick is plugged in, the hydraulic scheme can be saved. No values can be
changed.

9.14.6

Sending E-mails

ACTIVATE E-MAIL DISPATCH

CREATE RECEIVER LIST

Navigation 1:

Navigation 2:

→

Receiver list

Screen:

By pressing the button:

receiver list

a mail recipient can be added

Enter your email

address

the receiver’s E-mail addresses
can be set up.

E-Mail subject

The E-mail subject can be set up.

E-Mail dispatch can be activated

clear

the selected E-mail address gets
deleted off the receiver list

to return to the settings overview.

several values (errors, warnings,
info) can be chosen.

the  selected  E-mail  address  and
values  (error,  warnings,  info)  are
saved.

Содержание firestar de Luxe 18



























































































Результаты поиска

Содержание firestar de Luxe 18

Отзывы:

Похожие инструкции для firestar de Luxe 18

Бренды по названию

Популярные бренды

Herz firestar de Luxe 18, Руководство по эксплуатации

Результаты поиска

Содержание firestar de Luxe 18

Отзывы:

Похожие инструкции для firestar de Luxe 18

Бренды по названию

Популярные бренды