Herz firestar de Luxe 18 Скачать руководство пользователя страница 36

Страница: 36 / 90

Boiler control

9.13.3

Hot water tank

Navigation:

→

Hot water tank

Screen:

By pressing the button:

If fast start up is activated, the hot water tank is heated independently (maximum
loading time) to the requested set temperature

the „hot water tank status“ menu will be displayed

the menu for the "settings" will be displayed

the menu for the "Aggregate-

Test“ will be displayed

the menu for the "time

program,

barrier

times

and

circulation

times“ will be displayed

Display of the set times according to the time program:
the menu for the "time

program,

barrier

times

and

circulation

times“ will be displayed

Term

Description

Unit

Menu "Status"

Status 1

Hot water tank
temperature

Indicates the hot water tank upper zone temperature

°C

Hot water tank pump

Indicates the state of the hot water tank pump
(

→

only visible, if loading valve is inactivated)

Hot water tank
temperature bottom

Indicates the hot water tank bottom zone temperature

°C

Loading valve

Indicates the state of the loading valve (OFF/ON)
(

→

only visible, if loading valve is activated)

Circulation
temperature*

Indicates the circulation temperature

°C

Circulation pump*

Indicates the state of the circulation pump (ON/OFF)
(

→

only visible, if circulation pump is activated)

Menu "Settings"

Содержание firestar de Luxe 18



























































































Результаты поиска

Содержание firestar de Luxe 18

Отзывы:

Бренды по названию

Популярные бренды

Herz firestar de Luxe 18, Руководство по эксплуатации

Результаты поиска

Содержание firestar de Luxe 18

Отзывы:

Бренды по названию

Популярные бренды