Hendrickson Primaax EX 232 Скачать руководство пользователя страница 24

Страница: 24 / 77

PRIMAAX

EX / PRIMAAX

for International Truck Vehicles

17730-283

Special Tools

PRIMAAX QUICK WRENCH

FIGURE

5-1

Owatonna Tool Company (OTC) manufac-
tures a Hendrickson approved tool (OTC
Part Number 1768) for use on

PRIMAAX

suspensions (not for use on PRIMAAX EX
suspensions). Contact OTC for more infor-
mation at 800-533-6127.

■

Used to tighten to torque the cross tube
end cap bolts and longitudinal torque
rod top pad bolts.

■

Reduces maintenance time by eliminating the need to remove the tires to gain access to
the detachable end cap bolt.

NOTE

Due to some vehicle configurations and/or tire sizes wheel removal may be required.

■

Use the Quick Wrench tool with Hendrickson PRIMAAX suspensions detachable end cap
(see Figure 5-2) and on the longitudinal torque rod to top pad configuration illustrated in
Figure 5-3.

Any questions regarding the Quick Wrench tooling applications contact Tech Services

E-mail: [email protected]

Telephone: 630-910-2800

FIGURE 5-2

FIGURE 5-3

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

Содержание Primaax EX 232














































































Результаты поиска

Содержание Primaax EX 232

Отзывы:

Похожие инструкции для Primaax EX 232

Бренды по названию

Популярные бренды

Hendrickson Primaax EX 232, Руководство по обслуживанию

Результаты поиска

Содержание Primaax EX 232

Отзывы:

Похожие инструкции для Primaax EX 232

Бренды по названию

Популярные бренды