Hendrickson Primaax EX 232 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 77

background image

PRIMAAX

®

EX / PRIMAAX

®

for International Truck Vehicles

17730-283

75

PRIMAAX EX / PRIMAAX TROUBLESHOOTING GUIDE

CONDITION

POSSIBLE CAUSE

CORRECTION

Vehicle
leaning

Air spring not infl ated to
specifi cation or damaged

Repair air system and check ride height. See Ride Height Adjustment in the
Alignment & Adjustments Section in this publication.

Load not centered

Redistribute the load.

Frame twisted

Straighten the frame per vehicle manufacturer’s guidelines.

Broken support beam

Replace broken support beam assembly.

Axle housing bent or broken

Replace axle housing per vehicle manufacturer guidelines and align vehicle.

Loose U-bolts

Tighten U-bolts to specifi cations, see Preventive Maintenance Section.

Front suspension

Inspect and repair front suspension.

Suspension
will not reach
ride height

Suspension is overloaded

Redistribute load to correct weight.

Air Spring leaking or
damaged

Replace air spring.

Leak in air system

Inspect air fi ttings, see Air Fitting Inspection in the Preventive Maintenance Section
of this publication. If necessary, repair air system and check ride height. See Ride
Height Adjustment in the Alignment & Adjustments Section of this publication.

Air line obstructed or
improperly connected

Repair air system and check ride height. See Ride Height Adjustment in the
Alignment & Adjustments Section.

HCV dump port activated

Check HCV dump port for proper connection and function

Air springs
defl ate when
parked

Leak in air system

Inspect air fi ttings, see Air Fitting Inspection in the Preventive Maintenance Section
of this publication. If necessary, repair air system and check ride height. See Ride
Height Adjustment in the Alignment & Adjustments Section of this publication.

Misfunctioning Height Control
Valve

See test procedure in Preventive Maintenance Section, replace height control valve
as necessary.

Excessive frame
slope

Ride height set incorrectly

Adjust ride height to proper setting. See Ride Height Adjustment in the
Alignment & Adjustments Section. Contact Hendrickson Tech Services.

Suspension is overloaded

Redistribute load to correct weight

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

«
...
74
75
76
77
»

Содержание Primaax EX 232














































































Отзывы:

Нет отзывов

Похожие инструкции для Primaax EX 232

Бренд: GE Страницы: 100

Бренд: Garmin Страницы: 8

Passport 500 Pro

Бренд: Fender Страницы: 4

Бренд: TANDBERG Страницы: 12

Бренд: Valcom Страницы: 2

Бренд: JTS Страницы: 61

Бренд: Bluestream Страницы: 4

Бренд: Hogtunes Страницы: 12

Vocally Infinity

Бренд: ZYGO Страницы: 12

Бренд: Wavemaster Страницы: 32

Бренд: Galaxy Audio Страницы: 24

Бренд: LENCO Страницы: 24

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 18

Бренд: Panasonic Страницы: 100

Бренд: TDK Страницы: 9

RTM-ATCA-F120-OPT

Бренд: Emerson Страницы: 68

Бренд: CARVIN Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды