Hendrickson Primaax EX 232 Скачать руководство пользователя страница 68

Страница: 68 / 77

PRIMAAX

EX / PRIMAAX

for International Truck Vehicles

17730-283

Torque Specifi cations

PRIMAAX EX 232/462/692

9", 10½" Ride Height

HENDRICKSON RECOMMENDED TORQUE SPECIFICATIONS

NO.

COMPONENT

*QUANTITY

SIZE

**TORQUE VALUE

(in foot pounds)

Frame fasteners are furnished and installed by the vehicle manufacturer. Vehicle manufacturer may use an equivalent HUCK
fastener at frame mount.

Longitudinal Torque Rod to Frame Hanger

"-11 UNC

190-230

Longitudinal Torque Rod to Top Pad

"-14 UNF

525-575

U-beam Assembly to QUIK-ALIGN Bushing

1"-14 UNF

525-575

U-beam Assembly to Center D-Pin Bushing

¾"-16 UNF

275-325

U-bolt Locknuts

¾"-16 UNF

350-400

Upper Shock Absorber to Shock Bracket

¾"-10 UNC

175-200

Lower Shock Absorber to Bottom Cap

"-11 UNC

200-225

Air Spring Assembly to Upper Air Spring Bracket

½"-13 UNC

20-30

Air Spring Assembly to Lower Air Spring Mounting Bracket

½"-13 UNC

20-30

S-cam Support Bracket to Bottom Cap Mount

"-16 UNC

30-40

S-cam Support Bracket U-bolt Locknuts

"-18 UNC

20-30

NOTE:

* Quantities shown are per axle. Double for Tandem, Triple for Tridem.

** Torque values listed above apply only if Hendrickson supplied fasteners are used. If non Hendrickson fasteners are used, follow

torque specifi cation listed in vehicle manufacturer’s service manual.

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

Содержание Primaax EX 232














































































Результаты поиска

Содержание Primaax EX 232

Отзывы:

Похожие инструкции для Primaax EX 232

Бренды по названию

Популярные бренды

Hendrickson Primaax EX 232, Руководство по обслуживанию

Результаты поиска

Содержание Primaax EX 232

Отзывы:

Похожие инструкции для Primaax EX 232

Бренды по названию

Популярные бренды