Hendrickson Primaax EX 232 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 77

background image

17730-283

11

Parts Lists

Selection Guide and Aftermarket Service Kit

■

Bottom Cap and Longitudinal Torque Rod Assembly and Torque Rod Spacer

PRIMAAX EX 232/462/692• PRIMAAX 230/460/690

PINION

ANGLE

BOTTOM CAP

PART NO.

(2 per axle)

LONGITUDINAL TORQUE

ROD ASSEMBLY PART NO.

(2 per axle)

TORQUE ROD SPACER

PART NO.

(4 per axle)

**2.54

60556-035

*67274-510

**

3.61

67045-072

4.56

67045-071

5.72

67045-070

6.71

67045-069

**6.62

60556-100

*67274-540

**

7.67

67045-072

8.62

67045-071

9.77

67045-070

10.75

67045-069

**7.07

60556-105

*67274-540

**

8.12

67045-072

9.06

67045-071

10.22

67045-070

11.20

67045-069

* Torque rod bushings are non-serviceable, replacement requires complete torque rod assembly with bushings.

** Torque rod spacer not required.

■

U-beam Assembly Enhancement Aftermarket Service Kit

PRIMAAX EX SERIES

U-beam Assembly Enhancement Aftermarket Service Kit No. 69565-001, Axle Set

PART NO.

DESCRIPTION

QTY.

COMMENTS

69351-000

Sikafl ex 221 Polyurethane Sealant, 300 ml Tube

1

In the event any service to the suspension requiring disassembly of a
U-beam assembly equipped with integrated end caps, the Loctite 277,
tamper resistant caps and Sikafl ex 221 polyurethane sealant must
be properly installed to ensure components function to their highest
effi ciency. The enhancement components can be purchased individually
or as an aftermarket service kit.

69432-000

Tamper Resistant Cap

2

69570-000

Loctite

®

277 - 10 ml Bottle

1

50104-006

7

⁄

8

"-9 UNC 4.0" Hex Bolt

2

22962-042

7

⁄

8

" H-Coat Flat Washer

2

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

«
...
10
11
12
13
14
...
»

Содержание Primaax EX 232














































































Отзывы:

Нет отзывов

Похожие инструкции для Primaax EX 232

Бренд: Karel Страницы: 55

Бренд: JAMO Страницы: 8

Бренд: Unifone Страницы: 96

VRM-2200 PRO USB

Бренд: Omnitronic Страницы: 2

DUAL-VOX LTC-06

Бренд: B&G electronics Страницы: 6

Бренд: Rockville Страницы: 9

Бренд: Audio Technica Страницы: 2

Бренд: SoundMax Страницы: 43

Бренд: Alto Страницы: 18

Бренд: auna multimedia Страницы: 9

Бренд: Chiayo Страницы: 7

Бренд: VigaMusicTools Страницы: 28

Бренд: Steren Страницы: 23

Бренд: Hotec Страницы: 4

Бренд: Exibel Страницы: 84

Lyra MAP-AC2200

Бренд: Asus Страницы: 70

Бренд: Asus Страницы: 2

Бренд: JVC Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды