Hendrickson Primaax EX 232 Скачать руководство пользователя страница 46

Страница: 46 / 77

PRIMAAX

EX / PRIMAAX

for International Truck Vehicles

17730-283

Component Replacement

2. Remove shims (if equipped) and remove and discard the torque rod mounting fasteners, see

Figures 8-4 and 8-5.

3. Remove the longitudinal torque rod.

4. Inspect the mounting surfaces for any wear or damage, replace if necessary.

FIGURE 8-4

FIGURE 8-5

ASSEMBLY

1. Install the longitudinal torque rod.

2. Install the mounting fasteners and any shims that were removed, see Figures 8-4 and 8-5.

NOTE

Hendrickson recommends the use of Grade 8 bolts and Grade C locknuts be used for all torque
rod attachments.

NOTE

It is mandatory to have the vehicle at proper ride height prior to tightening the ¾" straddle
bushing and the

⁄

" top pad through bolt locknuts to torque specifications.

3. Tighten all fasteners to the required specification, see the Torque Specifications Section of

this publication.

4. When assembly is complete check the drive axle pinion angles, see the Alignment &

Adjustments Section of this publication.

5. Remove the wheel chocks.

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

Содержание Primaax EX 232














































































Результаты поиска

Содержание Primaax EX 232

Отзывы:

Похожие инструкции для Primaax EX 232

Бренды по названию

Популярные бренды

Hendrickson Primaax EX 232, Руководство по обслуживанию

Результаты поиска

Содержание Primaax EX 232

Отзывы:

Похожие инструкции для Primaax EX 232

Бренды по названию

Популярные бренды