Hendrickson Primaax EX 232 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 77

background image

PRIMAAX

®

EX / PRIMAAX

®

for International Truck Vehicles

17730-283

5

Important Safety Notice

SECTION 3

Important Safety Notice

Proper maintenance, service and repair are important to the reliable operation of the suspen-
sion. The procedures recommended by Hendrickson and described in this technical publication
are methods of performing such maintenance, service and repair.

The warnings and cautions should be read carefully to help prevent personal injury and to
assure that proper methods are used. Improper maintenance, service or repair may damage
the vehicle, cause personal injury, render the vehicle unsafe in operation, or void the manu-
facturer’s warranty.

Failure to follow the safety precautions in this manual can result in personal injury and/or
property damage. Carefully read and understand all safety related information within this pub-
lication, on all decals and in all such materials provided by the vehicle manufacturer before
conducting any maintenance, service or repair.

■

EXPLANATION OF SIGNAL WORDS

Hazard “Signal Words” (Danger • Warning • Caution) appear in various locations throughout
this publication. Information accented by one of these signal words must be observed to help
minimize the risk of personal injury to service personnel, or possibility of improper service meth-
ods which may damage the vehicle or render it unsafe.

This is the safety alert symbol. It is used to alert you to potential personal injury

hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.

Additional Notes or Service Hints are utilized to emphasize areas of procedural importance and
provide suggestions for ease of repair. The following definitions indicate the use of these signal
words as they appear throughout the publication.

INDICATES AN IMMINENTLY HAZARDOUS SITUATION, WHICH IF NOT AVOIDED, WILL RESULT IN
SERIOUS INJURY OR DEATH.

INDICATES A POTENTIAL HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, CAN RESULT IN SERIOUS
INJURY OR DEATH.

INDICATES A POTENTIAL HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, MAY RESULT IN MINOR OR
MODERATE INJURY.

NOTE

An operating procedure, practice condition, etc. which is essential to emphasize.

SERVICE HINT

A helpful suggestion that will make the servicing being performed a little easier and/or faster.

Also note that particular service operations may require the use of special tools designed for spe-
cific purposes. These special tools can be found in the “Special Tools” Section of this publication.

The torque symbol alerts you to tighten fasteners to a specified torque value. Refer to Torque
Specifications Section of this publication.

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

«
...
4
5
6
7
8
...
»

Содержание Primaax EX 232














































































Отзывы:

Нет отзывов

Похожие инструкции для Primaax EX 232

Бренд: NEC Страницы: 54

ELECTRA ELITE IPK II

Бренд: NEC Страницы: 174

Бренд: NEC Страницы: 268

DBS 576 Section 300

Бренд: Panasonic Страницы: 362

Бренд: Earthworks Страницы: 2

Бренд: Unimec Страницы: 48

Passport 500 Pro

Бренд: Fender Страницы: 4

Бренд: FeiYu Tech Страницы: 8

Бренд: auna multimedia Страницы: 124

kb sound Series

Бренд: EIS Страницы: 2

Бренд: US Shift Страницы: 44

Бренд: SKP Pro Audio Страницы: 6

PHONAK Roger Pass-around

Бренд: Sonova Страницы: 20

Бренд: Nady Systems Страницы: 2

Kenwood KMC-54WD

Бренд: JVCKENWOOD Страницы: 2

Бренд: Vertex Standard Страницы: 4

Бренд: Sanyo Страницы: 12

Бренд: Sanyo Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды