Hendrickson Primaax EX 232 Скачать руководство пользователя

Страница: 26 / 77

PRIMAAX

EX / PRIMAAX

for International Truck Vehicles

17730-283

Preventive Maintenance

FIGURE 6-1

FIGURE 6-2

INSPECTION AT 1,000 MILES

– PRIMAAX EX

1. Visually inspect suspension components with special attention to air springs and U-beam

assembly (support beam assembly, cross tube, and integrated end cap). Check for:

■

Proper suspension function

■

Any signs of unusual movement, loose or missing components

■

Any signs of abrasive or adverse contact with other components

■

Any damaged, bent or cracked parts

2. Check all fasteners for proper torque with special attention to the following suspension

connections.

■

QUIK-ALIGN fasteners, see Figure 6-2.

■

Torque rod to top pad fasteners, see Figure 6-2.

■

Clamp group fasteners (U-bolts), see Figure 6-3.

FIGURE 6-3

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

Содержание Primaax EX 232














































































Результаты поиска

Содержание Primaax EX 232

Отзывы:

Похожие инструкции для Primaax EX 232

Бренды по названию

Популярные бренды

Hendrickson Primaax EX 232, Руководство по обслуживанию

Результаты поиска

Содержание Primaax EX 232

Отзывы:

Похожие инструкции для Primaax EX 232

Бренды по названию

Популярные бренды