Hendrickson Primaax EX 232 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 77

background image

PRIMAAX

®

EX / PRIMAAX

®

for International Truck Vehicles

Product Description

4

17730-283

PRIMAAX

®

EX SPECIFICATIONS

PAX 232

PAX 232T

PAX 262S

PAX 462

PAX 462T

PAX 692

PAX 692T

Rating

23,000 lbs.

23,000 lbs.

26,000 lbs.

46,000 lbs.

46,000 lbs.

69,000 lbs.

69,000 lbs.

Installed Weight

1

558 lbs.

624 lbs.

578 lbs.

1,116 lbs.

1,248 lbs.

1,674 lbs.

1,873 lbs.

Axle Confi guration

Single

Single

Single

Tandem

Tandem

Tridem

Tridem

GCW Approval

2

95,000 lbs.

95,000 lbs.

142,000 lbs.

190,000 lbs.

190,000 lbs.

*

*

Site Travel Rating

3

30,000 lbs.

30,000 lbs.

33,000 lbs.

60,000 lbs.

60,000 lbs.

90,000 lbs.

90,000 lbs.

Axle Travel

4

8"

8"

8"

8"

8"

8"

8"

Ground Clearance

5

9.25"

9.25"

9.25"

9.25"

9.25"

9.25"

9.25"

Lift Axles

Approved

Approved

Approved

Approved

Approved

Approved

Approved

Ride Heights

6

9", 10½"

13"

9"

9", 10½"

13"

9", 10½"

13"

Engine Torque Restrictions

None

None

None

None

None

None

None

Axle Spacing

N/A

N/A

N/A

52"- 72.5"

52"- 72.5"

52"- 60"

52"- 60"

* See vehicle manufacturer’s recommendations.

1.

Installed weight includes complete suspension, torque rods, axle and frame brackets and all hardware. Published weight is based on
a standard PRIMAAX EX suspension compatible with drum brakes. Other configurations may vary.

2.

Contact Hendrickson or vehicle manufacturer for applications that may exceed GVW / GCW approval ratings.

3.

Site travel rating — operators using vehicles equipped with liftable pusher or tag axles must not exceed published ratings. Ratings
are limited to no more than five percent of vehicle operation at a speed not to exceed five mph. Liftable pusher or tag axles should be
raised (or unloaded) to improve vehicle maneuverability in off-road use or when vehicle is empty. Site travel ratings are consistent with
specifications and must not be exceeded.

4.

Axle travel may be limited by vehicle manufacturer; axle stop settings and shock absorber stroke may restrict suspension’s articulation.
Varying ride heights and configurations may restrict travel.

5.

Ground clearance is based on a standard PRIMAAX EX suspension with 11R22.5 tire size (19.6" SLR).

6.

For different ride height options, please contact Hendrickson, your truck manufacturer or dealer for further information.

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

«
...
3
4
5
6
7
...
»

Содержание Primaax EX 232














































































Отзывы:

Нет отзывов

Похожие инструкции для Primaax EX 232

Бренд: Magnavox Страницы: 23

Бренд: Sandstrom Страницы: 32

Microflex MX400D Series

Бренд: Shure Страницы: 20

Бренд: Akai Страницы: 38

Бренд: Magnavox Страницы: 25

Бренд: S.E.M. Страницы: 6

Бренд: Electro-Voice Страницы: 6

LINKBRIDGE LBO-DP12-R-2F

Бренд: Broadata Communications Страницы: 14

Бренд: Paso Страницы: 12

Бренд: Hama Страницы: 53

Midnight Blues MB1000H

Бренд: Audio Technica Страницы: 2

Бренд: Karma Страницы: 16

Бренд: LG Страницы: 24

Бренд: LG Страницы: 30

Бренд: LG Страницы: 24

Бренд: LG Страницы: 37

Бренд: LG Страницы: 32

Бренд: LG Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды