Hendrickson Primaax EX 232 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 77

background image

PRIMAAX

®

EX / PRIMAAX

®

for International Truck Vehicles

Component Replacement

54

17730-283

14.

Install the D-Pin fasteners, installing them from front to back, see Figure 8-22.

FIGURE 8-22

15.

Tighten the

7

⁄

8

" cross tube retaining bolt head to 525-575 foot pounds torque.

16.

Tighten D-Pin locknuts to 275-325 foot pounds torque and remove the cross tube
support.

17. Carefully clean the application area using a wire brush to remove loose paint and debris.

18. De-grease area with suitable de-greaser such as mineral spirits or brake cleaner. Ensure the

area is dry when done.

19. Install tamper resistant cap over fully tightened end cap bolt.

IRRITANT, SENSITIZER. SIKAFLEX 221 CAUSES EYE IRRITATION. MAY CAUSE SKIN/RESPIRATORY IRRITATION.
MAY CAUSE SKIN AND/OR RESPIRATORY SENSITIZATION AFTER PROLONGED CONTACT. MAY BE HARMFUL
IF SWALLOWED. AVOID DIRECT CONTACT. WEAR PERSONAL PROTECTIVE EQUIPMENT (CHEMICAL
RESISTANT GOGGLES/GLOVES/CLOTHING) TO PREVENT DIRECT CONTACT WITH SKIN AND EYES. USE
ONLY IN WELL VENTILATED AREAS. OPEN DOORS AND WINDOWS DURING USE. USE A PROPERLY FITTED
NIOSH RESPIRATOR IF VENTILATION IS POOR. WASH THOROUGHLY WITH SOAP AND WATER AFTER USE.
REMOVE CONTAMINATED CLOTHING AND LAUNDER BEFORE REUSE. STRICTLY FOLLOW ALL USAGE,
HANDLING AND STORAGE INSTRUCTIONS AS PROVIDED BY THE MANUFACTURER.

NOTE

Apply Sikaflex 221 polyurethane sealant at room temperature, refer to sealant manufacturer's
specifications.

FIGURE 8-23

FIGURE 8-24

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

«
...
53
54
55
56
57
...
»

Содержание Primaax EX 232














































































Отзывы:

Нет отзывов

Похожие инструкции для Primaax EX 232

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 36

SAPM71 - MINI HES W/CD PLAYER

Бренд: Panasonic Страницы: 12

Venture IP Telephone System

Бренд: Aastra Страницы: 24

Бренд: Aastra Страницы: 2

Бренд: Earthworks Audio Страницы: 4

Бренд: Garmin Страницы: 2

Бренд: Garmin Страницы: 2

Бренд: Garmin Страницы: 92

Passport Conference 2 Series

Бренд: Fender Страницы: 20

Бренд: Shure Страницы: 15

Electronics microphone

Бренд: SE Страницы: 4

Medialon MAS Pro Dante D

Бренд: 7th Sense Страницы: 2

Бренд: ION Страницы: 48

efector190 DTE810

Бренд: IFM Electronic Страницы: 38

Бренд: Microlab Страницы: 4

Бренд: Comica Страницы: 28

Бренд: Sima Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды