Hendrickson Primaax EX 232 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 77

background image

PRIMAAX

®

EX / PRIMAAX

®

for International Truck Vehicles

Preventive Maintenance

24

17730-283

SECTION 6

Preventive Maintenance

Following appropriate inspection procedures is important to help ensure the proper mainte-
nance and operation of the suspension system and component parts function to their highest
efficiency. Hendrickson recommends PRIMAAX EX / PRIMAAX heavy-duty rear suspensions be
inspected at pre-delivery, the first 1,000 miles of service and at the regular preventive main-
tenance intervals. Off-highway and severe service operating conditions require more frequent
inspections than on-highway service operation.

NOTE

Torque values shown in this publication apply only if Hendrickson supplied fasteners are
used. If non Hendrickson fasteners are used, follow the torque specification listed in the vehicle
manufacturer’s service manual.

AREAS OF INSPECTION

The inspection must include the following components:

➤

Air springs

•

Frame hanger bracket

•

Torque rods

•

Air supply and fittings

➤

QUIK-ALIGN connections

– Transverse

•

All fasteners

•

S-cam support tube bracket

– Longitudinal

➤

Clamp group

•

Shock absorbers

➤

U-beam assembly

➤

Top pad

•

Suspension wear and damage

•

Cross tube

➤

U-bolt locknuts

•

Tire wear

•

Support beam

•

End cap (if equipped)

➤

Signifi es performance critical components.

HENDRICKSON RECOMMENDED PREVENTIVE MAINTENANCE INTERVALS

PRE-DELIVERY INSPECTION

– PRIMAAX EX

1. Visually inspect the suspension for proper assembly.

2. Verify the lateral alignment of the drive axles are within the vehicle manufacturer’s toler-

ances, contact the vehicle manufacturer for the correct lateral alignment instructions.

3. Visually inspect the overall condition of the U-beam assembly (support beam assembly,

cross tube, and integrated end cap) for any damage.

4.

DO NOT RE-TORQUE

the integrated end cap (vehicles built

AFTER

March 2009), see

Figure 6-1.

5. Check all other fasteners for proper torque with special attention to the following suspen-

sion connections:

■

QUIK-ALIGN fasteners, see Figure 6-2.

■

Torque rod to top pad fasteners, see Figure 6-2.

■

Clamp group fasteners (U-bolts), see Figure 6-3.

6. Verify the ride height is within specification. Ride height is measured from the bottom of the

frame rail to the centerline of the axle.

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

«
...
23
24
25
26
27
...
»

Содержание Primaax EX 232














































































Отзывы:

Нет отзывов

Похожие инструкции для Primaax EX 232

T48S Skype For Business Edition

Бренд: Yealink Страницы: 3

Бренд: Panasonic Страницы: 1

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 20

digital slim -1400

Бренд: Fisher Страницы: 20

Бренд: auna multimedia Страницы: 124

Бренд: Shure Страницы: 36

Бренд: Electro-Voice Страницы: 2

Бренд: AKG Страницы: 26

Бренд: Hama Страницы: 76

Бренд: PCB Piezotronics Страницы: 12

Бренд: Akai Страницы: 20

Бренд: Sharp Страницы: 68

Бренд: Sharp Страницы: 112

Бренд: Kongsberg Страницы: 152

Бренд: Vertex Standard Страницы: 4

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды