HEAT GLO CERONA-36-IFT Скачать руководство пользователя страница 20

Страница: 20 / 59

Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21

• If the combustible materials are not in place at the time

of install the elbow heat shield may be screwed to the

exhaust pipe (see Figure 4.11). Cut the tabs as shown

and bend down. Secure the heat shield to the pipe

maintaining 3 inch to 4 inch between the pipe and shield.

Refer to Cinch Pipe and Termination Cap installation in

structions.
• Continue adding vent components, locking each

succeeding component into place.

• Ensure that each succeeding vent component is securely

fitted and locked into the preceding component in the

vent system.

• 90º elbows may be installed and rotated to any point

around the preceding component’s vertical axis. If an

elbow does not end up in a locked position with the

preceding component, attach with a minimum of two (2)

sheet metal screws.

Figure 4.11

SCREW

3 in.

(76 mm)

F. Install Support Brackets

Refer to Cinch Pipe and Termination Cap installation in

structions.

General Rules:

• SUBTRACT 3 ft from the total H measurement for each

90º elbow installed horizontally.

• SUBTRACT 1-1/2 ft from the total H measurement for

each 45º elbow installed horizontally.

• A maximum of three 90º elbows (or six 45º elbows) may

be used in any vent configuration. Some elbows may be

installed horizontally. See Figure 4.16.

• Elbows may be placed back to back anywhere in the

system.

•

Any 90º elbow may be replaced with two back to back

45º elbows.

• When penetrating a combustible wall, a wall shield

firestop must be installed.

• When penetrating a combustible ceiling, a ceiling firestop

must be installed.

• Horizontal runs of vent do not require vertical rise;

horizontal runs may be level.

• Horizontal termination cap should have a 1/4 inch

downward slant to allow any moisture in cap to be

released.

G. Vent Diagrams

Содержание CERONA-36-IFT




























































Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды

HEAT GLO CERONA-36-IFT, Руководство по установке

Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды