HEAT GLO CERONA-36-IFT Скачать руководство пользователя страница 59

Страница: 59 / 59

Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21

B. Accessories

Remote Controls, Wall Controls and Wall
Switches

Follow the instructions supplied with the control installed

to operate your appliance:
For safety:
• Install a switch lock or a wall/remote control with child

protection lockout feature.

• Keep remote controls out of reach of children.
See your dealer if you have questions.

Heat & Glo, a brand of Hearth & Home Technologies

7571 215

Street West, Lakeville, MN 55044

www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns.

For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

Optional Heat Management Systems Kits

After a qualified service technician has installed the heat

management system, follow the instructions supplied with

the kit for operation. Contact your dealer if you have

questions.

Note:

Optional heat management systems kit must be

installed while the top of the appliance are accessible.

Install approved accessories per instructions included

with accessories. Contact your dealer for a list of ap

proved accessories.

WARNING! Risk of Fire and Electric Shock!

Use ONLY

Hearth & Home Technologies-approved optional acces-

sories with this appliance. Using non-listed accessories

could result in a safety hazard and will void the warranty.

Содержание CERONA-36-IFT




























































Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды

HEAT GLO CERONA-36-IFT, Руководство по установке

Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды