HEAT GLO CERONA-36-IFT Скачать руководство пользователя страница 26

Страница: 26 / 59

Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21

D. Install Attic Insulation Shield

WARNING!

Fire Risk.

The use of an attic

shield is required to prevent loose materials

or insulation from contacting the vent causing

overheating and a fire.

The International Fuel Gas Code requires an

attic shield constructed of 26 gauge minimum

steel that extends at least 2 in. (51 mm) above

insulation.
• Attic insulation shields must meet specified

clearances to combustible materials and be

secured in place.

• An attic insulation shield kit is available from

Hearth & Home Technologies. Contact your

dealer to order. Install attic insulation shield

according to instructions included with kit.

C. Ceiling Firestop/Floor Penetra-

tion Framing

WARNING! Risk of Fire! DO NOT pack insu-

lation around the vent.

Maintain clearances to

vent to prevent overheating.

A ceiling firestop

MUST

be used between

floors and attics.

•

DVP pipe only

- Frame an opening 10 in.

by 10 in. (254 mm by 254 mm) whenever

the vent penetrates a ceiling/floor (see

Figure 5.3).

• Frame the area with the same sized lumber

as used in ceiling/floor joist.

• The ceiling firestop may be installed above or

below the ceiling joists when installed with an

attic insulation shield. It must be under joists

between floors that are not insulated. Refer

to Figure 5.4.

• Secure in place with nails or screws.

Figure 5.3 Installing Ceiling Firestop

Figure 5.4 Installing the Attic Shield

INSTALL ATTIC INSULATION SHIELDS

BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

CEILING FIRESTOP

INSTALLED BELOW CEILING

CEILING FIRESTOP

INSTALLED ABOVE CEILING

ATTIC ABOVE

PIPE
DVP

10 in. (254 mm)

Содержание CERONA-36-IFT




























































Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды

HEAT GLO CERONA-36-IFT, Руководство по установке

Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды