HEAT GLO CERONA-36-IFT Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 59

background image

Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21

6

2

2

Getting Started

A. Design and Installation Considerations

WARNING! Risk of Fire or Explosion!

Read all instruc-

tions before starting the installation.

Direct vent gas appliances are designed to operate with

all combustion air siphoned from outside of the building

and all exhaust gases expelled to the outside. No addi

-

tional outside air source is required.
Installation MUST comply with local, regional, state and

national codes and regulations. Consult insurance carrier,

local building inspector, fire officials or authorities having

jurisdiction over restrictions, installation inspection and

permits.
Before installing, determine the following:
•  Where the appliance is to be installed.
•  The vent system configuration to be used.
•  Gas supply piping requirements.
•  Provisions for optional heat management system.
•  Electrical wiring requirements.
•  Framing and finishing details.
•  Whether optional accessories—devices such as a fan,

wall switch, or remote control—are desired.

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualified

service technician, service agency or your dealer.

B. Good Faith Wall Surface

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

6 in.

18 in.

24 in.

30 in.

36 in.

TO CEILING

12 in.

APPLIANCE FRONT

200 °F

183 °F

165 °F

155 °F

140 °F

125 °F

APPLIANCE

OPENING

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recommends

HHT Factory Trained or NFI certified professionals.

Figure 2.1 Good Faith Wall Surface Temperatures Above

Appliance

NOTICE:

Surface temperatures listed above are taken with

a temperature measuring probe as prescribed by the test

standard used for appliance certification. Temperatures

on walls or mantels taken with an infrared thermometer

may yield increased temperatures of up to 30

°

F (17

°

C) or

more depending on the thermometer settings and material

characteristics being measured. Use appropriate finishing

materials that are able to withstand these conditions. For

additional finishing guidelines, see Section 10.

If installing a television (TV) above the appliance, see

Section 3 of the appliance Owner’s Manual.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

6 in.

18 in.

24 in.

30 in.

TO CEILING

12 in.

150°F

APPLIANCE FRONT

145°F

135°F

125°F

115°F

OPTIONAL PASSIVE HEAT KIT INSTALLED

APPLIANCE

OPENING

Figure 2.2 Good Faith Wall Surface Temperatures Above

Appliance with Passive Heat Kit Installed

«
...
4
5
6
7
8
...
»

Содержание CERONA-36-IFT




























































Отзывы:

Нет отзывов

Похожие инструкции для CERONA-36-IFT

Бренд: Endless Summer Страницы: 24

Бренд: Paloform Страницы: 14

MANDALAY Series

Бренд: Warnock Hersey Страницы: 38

Madrona MF28JLN NG

Бренд: Valor Страницы: 42

Бренд: Valor Страницы: 48

Argon Built 3 Sided

Бренд: Stanley Страницы: 26

Бренд: barbas Страницы: 100

Бренд: ELEMENTI Страницы: 60

Бренд: Element4 Страницы: 12

Бренд: Faber Страницы: 24

Бренд: Enviro Страницы: 48

Vail L-FT769PST

Бренд: Sunjoy Страницы: 5

Бренд: Valor Страницы: 46

Бренд: Febo Flame Страницы: 11

Crea7ionEVO PLUS 1200

Бренд: GlammFire Страницы: 52

Бренд: IHP Страницы: 36

RUTHERFORD 50-B

Бренд: Heat&Glo Страницы: 48

Бренд: Heat&Glo Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды