HEAT GLO CERONA-36-IFT Скачать руководство пользователя страница 56

Страница: 56 / 59

Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21

Figure 12.6 PVI-SLP-B Vent Components

Required Wire Harness

DESCRIPTION

PART NUMBER

10 FT PV Wire Harness

PVI-WH10

20 FT PV Wire Harness

PVI-WH20

40 FT PV Wire Harness

PVI-WH40

60 FT PV Wire Harness

PVI-WH60

80 FT PV Wire Harness

PVI-WH80

100 FT PV Wire Harness

PVI-WH100

PVI-SLP-B

Power Vent Inline

SLP-LPC

SLP Low Profile Cap

(Approved for use with PVI-SLP-B only)

Note:

Wire harnesses required to power the PVI-SLP-B connect to the appliance and are ordered separately from

PVI-SLP-B. Contact your dealer to order.

16 IN.

406 mm

15 IN.

(381 mm)

16-11/16 IN.

(424 mm)

9-3/16 IN.

(233 mm)

4-1/2 IN.

114 mm

16-11/16 IN.

424 mm

13-5/8 IN.

(346 mm)

12-1/2 IN.

(318 mm)

12-1/2 IN.

318 mm

20-3/4 IN.

527 mm

13-5/8 IN.

346 mm

EFFECTIVE LENGTH

32 IN. (813 mm) MIN.

35 IN. (889 mm) MAX.

DVP-2SL

Adapter

Note:

The PVI-SLP-B requires one of the following options to be installed on this appliance.

Option A: IFT-RC400 and/or IFT-WFM, IFT-ACM and IntelliFire App that can be downloaded from the app store.

Option B: IFT-RC150, IFT-ACM, IFT-WFM and an IntelliFire App that can be downloaded from the app store. These

accessories are purchased separately from the PVI-SLP-B. Contact your dealer to order.

Содержание CERONA-36-IFT




























































Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды

HEAT GLO CERONA-36-IFT, Руководство по установке

Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды