HEAT GLO CERONA-36-IFT Скачать руководство пользователя страница 40

Страница: 40 / 59

Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21

Finishing

Risk of Fire!
DO NOT

apply combustible materials beyond the min-

imum clearances. Comply with all minimum clearanc-

es to combustibles as specified in this manual.

Ma-

terials overlapping into non-combustible zones could

ignite and will interfere with air flow through decora

tive barrier fronts.

• Metal front of appliance may be covered with non-

combustible materials only.

• Facing and/or finishing materials must not interfere

with air flow through decorative barrier fronts, removal

of decorative barrier fronts or access for service.

• Facing and/or finishing materials must never

overhang into the glass opening.

• Observe all clearances when applying combustible

materials.

• Seal gaps between the finished wall and appliance

top and sides using a 300 ºF minimum sealant. Refer

to Figure 10.1.

WARNING

A. Facing Material

Risk of Fire
• Non-combustible clearances

MUST

maintained.

• Sheetrock, wood or other combustibles must

NOT

be used as sheathing or facing in the

non-combustible zone.

• See

Section 3

for proper clearances.

• See

Section 1

for combustible/non-

combustible definitions.

WARNING

Figure 10.1

CERONA-36-IFT

in.

16-3/4 43-5/8

1245

425

1108

CERONA-42-IFT

in.

45-1/4 16-3/4 50-5/8

1149

425

1286

1 in.

(25)

CEILING

COMBUSTIBLE

SHEATHING

NON-COMBUSTIBLE

FACING MATERIAL

IN SHADED AREAS

APPLIANCE

ARCH OPENING

CLEARANCE

TO CEILING

MINIMUM

BOTTOM OF APPLIANCE

TO BOTTOM OF

NON-COMBUSTIBLE

FACING MATERIAL

Содержание CERONA-36-IFT




























































Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды

HEAT GLO CERONA-36-IFT, Руководство по установке

Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды