HEAT GLO CERONA-36-IFT Скачать руководство пользователя страница 45

Страница: 45 / 59

Heat & Glo • CERONA-36-IFT, CERONA-42-IFT Installation Manual • 2558-980 Rev. C • 3/21

Appliance Setup

A. Remove the Shipping Materials

Remove shipping materials from inside or underneath

the firebox.
• The splatter guard is a piece of corrugated material

used to protect the appliance during the installation

process before finishing work on the whole hearth is

complete. Splatter guards may be factory installed

or accompany the decorative barrier front of the ap

pliance, depending on the appliancee model. Splat

ter guards must be removed before appliance is

fired.

WARNING! Risk of Fire!

Close the ball valve before in-

stalling the splatter guard to prevent accidental lighting.

Remove the splatter guard before lighting the appliance.

D. Install Media/Embers

C. Inspect Firebox

Surface cracking or crazing of firebrick material is normal

and expected. All cracks are acceptable and do not

require replacement of the appliance or the firebox with

the exception of:
• Cracks compromising the surface plane of the firebox.

See Figure 11.1.

Figure 11.1 Surface plane of firebox is compromised and should be

replaced.

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated

inside the firebox or underneath in the control cavity.

WARNING! Risk of Explosion!

Follow ember placement

instructions in manual. DO NOT place embers directly over

burner ports. Replace ember material annually. Improperly

placed embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. To place

the ember material:
• There are two types of ember shipped with the appliance.

Glowing Embers

for the burner surface and Mystic

Embers for the floor of the appliance.

• Glowing Embers CANNOT be placed directly over ports.

Care should be taken not to cover the lighting trail of

ports (from back to front).

• When placing Glowing Embers

onto the burner care

should be taken so that the ports are not covered. Place

the dime-size ember pieces in front and behind of the

port trail, but not on or in between the ports (see Figure

11.2). Failure to follow procedure will likely cause lighting
and sooting problems.

• Place Mystic Embers on areas of base refractory away

from port holes. Use this material to give the appliance

a realistic ash bed.

• Save the remaining ember materials for use during

appliance servicing. The embers provided should be

enough for 3 to 5 applications.

Figure 11.2 Placement of Embers

GLOWING EMBER PLACEMENT

Содержание CERONA-36-IFT




























































Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды

HEAT GLO CERONA-36-IFT, Руководство по установке

Результаты поиска

Содержание CERONA-36-IFT

Отзывы:

Похожие инструкции для CERONA-36-IFT

Бренды по названию

Популярные бренды