Heat & Glo REVO-H31 Скачать руководство пользователя страница 59

Страница: 59 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

C. In-Wall - Minimum Non-Combustible

Facing Clearances

Figure 11.9

Figure 11.10

NON-COMBUSTIBLE BOARD

NON-COMBUSTIBLE FACING

FINISHING

STRIPS

ZERO CLEARANCE TO

IN-WALL TUB OPENING

(TOP, BOTTOM AND SIDES)

1-1/2 IN. MAX.

THICKNESS

NOTE: FINISHING STRIPS CAN BE USED TO

MAINTAIN PROPER CLEARANCE.

SEE FIGURE 11.5 FOR INSTALLATION.

SHEET ROCK

1/2 IN. MAX.

THICKNESS

REMOVE CLIPS

APPLIANCE FINISHING STRIP

REMOVE APPLIANCE FINISHING STRIP

NOT USED WITH IN-WALL KIT

NON-COMBUSTIBLE BOARD

NON-COMBUSTIBLE FACING

STUDIO OR FRAME DECORATIVE FRONT

SHEET ROCK

1-1/2 IN.

THICK MAX.

NOTE: FINISHING STRIPS CAN BE USED TO

MAINTAIN PROPER CLEARANCE.

SEE FIGURE 11.5 FOR INSTALLATION.

DO NOT BLOCK

CONVECTION VENTS

STUDIO OR FRAME

DECORATIVE FRONT

NOTICE:

The In-Wall application is not compatible with

the Radius decorative front.



Содержание REVO-H31






































































Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды

Heat & Glo REVO-H31, Руководство по установке

Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды