Heat & Glo REVO-H31 Скачать руководство пользователя страница 48

Страница: 48 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

DO NOT BLOCK CONVECTION VENTS

Figure 10.5 Radius Door

B. Facing and Finishing - Radius Decorative

Front (1 Inch Max. Non-Combustible)

SHEET ROCK

FINISHING MATERIAL

NON-COMBUSTIBLE

1 IN. THICK MAX.

WALL

ZERO CLEARANCE

(TO APPLIANCE OUTER WRAP)

ALL 4 SIDES

NOTE: The Radius

front will rest an

additional 1 inch from

the appliance when

finishing up to the

appliance outer wrap.

APPLIANCE OUTER WRAP

RADIUS

DOOR

Figure 10.6 Radius Door - Side View

WALL

SHEET ROCK

NON-COMBUSTIBLE

FINISH MATERIAL

1 IN. THICK MAX.

OUTER WRAP

RADIUS DOOR

Figure 10.7 Radius Door - Non-Combustible Facing Diagram

The following instructions apply to facing and finishing

materials up to one inch thick, made of non-combustible

material, finished up to the appliance outer wrap and

used with the Radius decorative front. For the definition

of non-combustible materials, see Section 1.E.

Remove and discard finishing strip before installation of

appliance. See Figure 10.4. The finishing strip is not be

used with the Radius decorative front.

REMOVE CLIPS

FINISHING STRIP

Figure 10.4 Remove Finishing Strip (Not used with Radius

Decorative Front)



Содержание REVO-H31






































































Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды

Heat & Glo REVO-H31, Руководство по установке

Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды