Heat & Glo REVO-H31 Скачать руководство пользователя страница 54

Страница: 54 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

2. A Corrugated Template may be used to simplify the in-

stallation process. Contact your dealer or see Service

Parts section in Owner’s manual to order. Using the

template for installations of the REVO will help when

locating the gas and electrical connections for the ap-

pliance. Install the corrugated template as shown in

Figure 11.2. Use blocks to position the corrugated

template in regards to depth.

3. Bring electrical and gas hookups to location designat

ed by markings on corrugated template. Remove tem

plate and blocks when utility installation is complete.

Note:

Hard-piped gas connections must be terminated

with a specific “Z” dimension depth. See references to “Z”

dimension in Figure 11.2. Terminating the Hard-piped gas

connection with the proper “Z” dimension will simplify the

process of connecting the gas to the appliance.

FRAMING

DIMENSIONS

V12

20-1/8 in.

43-1/8 in.

4 in. min.

S21

29-3/8 in.

40-1/2 in.

4 in. min.

H31

39-3/8 in.

39 in.

4 in. min.

Figure 11.1 Framing Dimensions and In-Wall Tub - Clearances

The Revo may be installed recessed into the wall using

the In-Wall Tub. The Frame and Studio doors are com-

patible with this type of installation. In-Wall installation is

not compatible with the Radius decorative front.

WARNING! Risk of Fire!

Comply with all minimum clear-

ances as specified. Framing closer than the minimums listed

must be constructed entirely of noncombustible materials

(i.e., steel studs, concrete board, etc.)

1. Prepare 2 in. x 6 in. framing as shown in Figure 11.1.

In-Wall Installation

A. wall and Appliance Preparation

Note:

2 X 4 framing is not recommended in geographical

regions that require an R-19 insulation value.

C=4 IN. MIN.

FINISHED

FLOOR

WALL - FRAMED

ZERO

CLEARANCE

(BOTTOM)

ZERO

CLEARANCE

(BACK)

OPTIONAL

FINISHING

STRIPS

SEE DIMENSION B

FOR CLEARANCE

(TOP)

SEE DIMENSION A

FOR CLEARANCE

(SIDE)

IN-WALL TUB CLEARANCES

NOTICE:

The In-Wall application is not compatible with

the Radius decorative front.

Содержание REVO-H31






































































Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды

Heat & Glo REVO-H31, Руководство по установке

Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды