Heat & Glo REVO-H31 Скачать руководство пользователя страница 50

Страница: 50 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

C. Facing and Finishing - Radius Decorative

Front (4 Inch Maximum Non-Combustible)

DO NOT BLOCK CONVECTION VENTS

WALL

SHEET ROCK

NON-COMBUSTIBLE

FINISH MATERIAL

4 IN. THICK MAX.

RADIUS DOOR

Figure 10.10 Radius Door

4 IN. MAX.

(MEASURED FROM

SHEET ROCK)

DOOR FLUSH TO

SHEET ROCK

NON-COMBUSTIBLE

MATERIAL

4 IN. THICK MAX.

WALL

SHEET ROCK

RADIUS DOOR

*GAP =1/2 IN.

*The gap around the decorative front is needed for removing

and installing the Radius decorative front.

Figure 10.11 Radius Door

*1/2 IN.

NON-COMBUSTIBLE

FINISH MATERIAL

CLEARANCE TO

RADIUS DOOR

*1/2 IN.

*The gap around the decorative front is needed for removing

and installing the Radius decorative front.

Figure 10.12 Radius Door - Clearance to Non-Combustible

Finishing Material

REMOVE CLIPS

FINISHING STRIP

Remove and discard finishing strip before installation of

appliance. See Figure 10.4. The finishing strip is not be

used with the Radius decorative front.

Figure 10.9 Remove Finishing Strip (Not used with Radius

Decorative Front)



Содержание REVO-H31






































































Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды

Heat & Glo REVO-H31, Руководство по установке

Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды