Heat & Glo REVO-H31 Скачать руководство пользователя страница 42

Страница: 42 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

A. General Information

WARNING! Risk of Shock or Explosion! DO NOT

wire

110-120 VAC to the valve or to the appliance wall switch.

Incorrect wiring will damage controls.

NOTICE:

This appliance must be electrically wired

and grounded in accordance with local codes or, in the

absence of local codes, with

National Electric Code

ANSI/NFPA 70-latest edition

or the

Canadian Electric

Code CSA C22.1.

• Wire the appliance junction box to unswitched 110-

120 VAC. This is required for proper operation of the

appliance.

• A 110-120 VAC circuit for this product must be protected

with ground-fault circuit-interrupter protection, in

compliance with the applicable electrical codes, when

it is installed in locations such as in bathrooms or near

sinks.

• Low voltage and 110-120 VAC voltage cannot be shared

within the same wall box.

Accessories Requirements

• This appliance may be used with a wall switch, wall

mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved

accessories should be done now to avoid reconstruction.

Follow instructions that come with those accessories.

Electrical Information

Figure 8.1 Junction Box Detail

NOTICE: DO NOT

wire 110-120 VAC to wall switch.

Junction Box Installation

If the box is being wired from the

INSIDE

of the appliance:

• Remove the screw attaching the junction box/receptacle.

Rotate the junction box inward to disengage it. See

Figure 8.1.

• Pull the electrical wires from outside the appliance through

the opening into the valve compartment and secure wires

with a Romex connector. See Figure 8.1.

• Make all necessary wire connections to the junction

box/receptacle and position and secure the junction box/

receptacle into its original position.

Electrical Service and Repair

WARNING! Risk of Shock!

Label all wires prior to dis-

connection when servicing controls. Wiring errors can

cause improper and dangerous operation. Verify proper

operation after servicing.

WARNING! Risk of Shock!

Replace damaged wire with

type 105º C rated wire. Wire must have high temperature

insulation.

Romex

Connector

Ground

Connection

Attach Screw

Содержание REVO-H31






































































Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды

Heat & Glo REVO-H31, Руководство по установке

Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды