Heat & Glo REVO-H31 Скачать руководство пользователя страница 37

Страница: 37 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

120º

Figure 7.5 Securing Vertical Pipe Sections

120º

Figure 7.6 Securing Horizontal Pipe Sections

B. Installing Slip Sections

• Slide the inner flue of the slip section into the inner flue

of the pipe section and the outer flue of the slip section

over the outer flue of the pipe section. See Figure 7.3.

• Slide together to the desired length.

Figure 7.3 Slip Section Pilot Holes

Figure 7.4 Screws into Slip Section

Pilot hole

NOTICE:

When installing a vent system with an HRC

termination cap, all pipe system joints shall be sealed

using a high temperature silicone sealant (300ºF minimum

continuous exposure rating).

•

Apply a bead of silicone sealant (300ºF minimum

continuous exposure rating) inside the female outer pipe

joint prior to joining sections.

•

Only outer pipes are sealed, sealing the inner flue is not

required.

•

All unit collar, pipe, slip section, elbow and cap outer

flues shall be sealed.

• Continue adding pipe as necessary following instructions

in “Assembling Pipe Sections.”

NOTICE:

If slip section is too long, the inner and outer

flues of the slip section can be cut to the desired length.

• Maintain a 1-1/2 in. (38 mm) overlap between the slip

section and the pipe section.

• Secure the pipe and slip section with two screws no

longer than 1/2 in. (13 mm), using the pilot holes in the

slip section. See Figure 7.4

C. Secure the Vent Sections

• Vertical runs originating off the top of the appliance, with

no offsets, must be supported every 8 ft. (2.44 m) after

the maximum allowed 25 ft. (7.62 m) of unsupported rise.

• Vertical runs originating off the rear of the appliance, or

after any elbow, must be supported every 8 ft. (2.44 m).

• Horizontal runs must be supported every 5 feet (1.52

m).

• Vent supports or plumbers strap (spaced 120º apart)

may be used to support vent sections. See Figures 7.5

and 7.6.

• Wall shield firestops may be used to provide horizontal

support to vent sections.

• SLP ceiling firestops have tabs that may be used to

provide vertical support.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support may allow vent to sag and separate.

Use vent run supports and connect vent sections per in-

stallation instructions.

DO NOT

allow vent to sag below

connection point to appliance.

Содержание REVO-H31






































































Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды

Heat & Glo REVO-H31, Руководство по установке

Результаты поиска

Содержание REVO-H31

Отзывы:

Похожие инструкции для REVO-H31

Бренды по названию

Популярные бренды