Hardi HC 8500 Скачать руководство пользователя страница 68

Страница: 68 / 184

4 - System setup

4.42

28.

Press

to confirm the settings and

continue.

29.

Select Primary Speed Source.

•

Self-Propelled sprayer:

Can select between “Hardi” or “Display GPS”
as speed source.

•

SARITOR sprayer only:

Always select “Display GPS” as speed source.

NOTE! If “Display GPS” is selected, the “Hardi”

option must be selected as backup source.

ATTENTION! For additional information see

“Speed Input Settings” on page 4.70.

30.

“Hardi” is now selected as Primary Source.

ATTENTION! No other source can be
selected when “Hardi” is selected as primary
source.

Press

to confirm the selection.

Operating Configuration Wizard: Vehicle

Select Vehicle

Offsets

Antenna Location from Rear Axle

Antenna Location from Centerline

Antenna Height from Ground

Dispensing Location from Rear Axle

Dispensing Location from Centerline

Behind

In Front

Operating Configuration Wizard: Speed Source

Primary Source

Backup Source

Auxiliary Device Channel

Auxiliary Channel Calibration

Calibrate

Distance

Pulses / 100 ft

Display GPS

Auxiliary Device

Radar

Operating Configuration Wizard: Speed Source

Primary Source

Hardi

Содержание HC 8500

























































































































































































Результаты поиска

Содержание HC 8500

Отзывы:

Hardi HC 8500, Руководство оператора, Страница: 68 / 184

Результаты поиска

Содержание HC 8500

Отзывы: