Hardi HC 8500 Скачать руководство пользователя страница 121

Страница: 121 / 184

4 - System setup

4.95

OnTrac Tuning

•

Motor Aggressiveness

Determines how aggressively the motor
engages.

•

Heading Aggressiveness

Determines how aggressively the system
reacts to achieve the correct heading.

•

Cross-Track Error

Adjusts how aggressively the vehicle reacts
to changes in cross-track error.

Lightbar

•

LED Spacing

Enter the distance represented by each
square of the lightbar (6-72 in.).

•

Mode

•

Chase

Center the vehicle by following the
indicator lights.

•

Pull

Center the vehicle by turning in the
opposite direction of the indicator
lights on the lightbar.

•

External Lightbar LED Brightness

If applicable, press

enter in a number specifying the brightness
of the LED lights on the optional L160
external lightbar. The number 1 is the dimmest and 10 is the brightest. Default is 5.

OnTrac Tuning

Nudge

Tramlines

Shift

Lightbar

Save

Pause

Guidance Options

Steering

Motor Aggressiveness

OnTrac Tuning

Heading Aggressiveness

Cross-Track Error

Remark A

Lightbar

Nudge

Tramlines

Shift

Lightbar

Spacing

External Lightbar

LED Brightness

Mode

Chase

Save

Pause

Remark A

Guidance Options

Содержание HC 8500

























































































































































































Результаты поиска

Содержание HC 8500

Отзывы:

Hardi HC 8500, Руководство оператора, Страница: 121 / 184

Результаты поиска

Содержание HC 8500

Отзывы: