Hardi HC 8500 Скачать руководство пользователя страница 106

Страница: 106 / 184

4 - System setup

4.80

Lightbar Settings

Setup

•

LED Spacing

Enter the distance represented by each
square of the lightbar (3-182 cm).

•

Mode

•

Chase

Center the vehicle by following the
indicator lights.

•

Pull

Center the vehicle by turning in the
opposite direction of the indicator
lights on the lightbar.

•

External Lightbar LED Brightness

If applicable, press

enter in a number specifying the brightness

of the LED lights on the optional L160

external lightbar. The number 1 is the dimmest setting and 10 is the brightest. Default setting is 5.

Guidance Tab on Mapping Toolbox

The Guidance Tab on the Mapping Toolbox allows you to you can create a new pattern, load
an existing pattern, or adjust Guidance Options and Guidance Settings. This tab changes its
appearance after you create or load a pattern.

Before you create any patterns, the map screen’s Guidance Tab appears as shown.

NOTE! Guidance pattern will default to the one last used. Guidance patterns can be
set to widths up to 2000 ft (609 m).

Lightbar Settings

External Lightbar

LED Brightness

Lightbar Settings

Spacing

Mode

Chase

New

Pattern

Load

Pattern

Manage
Patterns

Guidance

Содержание HC 8500

























































































































































































Результаты поиска

Содержание HC 8500

Отзывы:

Hardi HC 8500, Руководство оператора, Страница: 106 / 184

Результаты поиска

Содержание HC 8500

Отзывы: