background image

64

Preventive Maintenance and Installation

P/N: SM-ACP215-01-EN(AB)

Haemonetics

®

 ACP-215

®

 Service Manual

System Cleaning

Warning: Haemonetics recommends handling all biologically 
contaminated materials pursuant to those policies and procedures 
dictated by the medical facility’s infection control plan, as legally 
required by the OSHA Blood Borne Pathogen Standard.

Caution: 

Never use organic solvents (e.g., acetone) acids, bases, chlorine

solutions, phenolics or soap to clean any portion of the device. 

Cleaning 

Agents

Haemonetics recommends using a 1:10 mixture of household bleach and 
water as a cleaning solution for blood borne pathogens.

Cleaning Agents NOT Compatible With the Device

The commercial cleaners listed in 

Table 5 on page 64

 should not be used as a 

daily 

cleaner on the device.

Other Cleaning Agents

Table 5 on page 64

 lists the most commonly used cleaners that are not 

recommended. This list is not intended to be all inclusive. For cleaning agents 
that are not on the above list and you are not sure about, please call 
Haemonetics Corporation to determine if the cleaning agent is appropriate for 
use in daily maintenance.

 

In the United States, product support and field service can be contacted 
through the Haemonetics Customer Care Center at 1-800-537-2802.

Table 5, Cleaning agents not compatible with the device

Cleaner

Part(s) Affected

Results

Pro-Tech

Pinch valve housing, centrifuge 

cover window, and membrane 

panel.

May cause 

cracking and 

hazing.

Dispatch

Pinch valve housing, centrifuge 

cover window, membrane 

panel, DPM and SPM sleeves.

May cause 

cracking and 

hazing.

CitriGuard II

Pinch valve housing, centrifuge 

cover window, and membrane 

panel.

May cause 

cracking and 

hazing.

Alcohol
Should never be 

used to clean the 

air detectors.

Air detector.

May cause the air 

detector housing to 

degrade.

Содержание ACP 215



























































































































































































Отзывы: