manualshive.com logo in svg

Hach DR 6000, Руководство пользователя

Поделиться
Скачать
Hach DR 6000 Скачать руководство пользователя страница 65

65

Standard programs

Measures to identify other interference factors:

Checklist:

1.

Check if the procedure is completed correctly:

a.

Are the reagents added in the correct order?

b.

Is enough time allowed for colour development?

c.

Is the correct glassware in use?

d.

Is the glassware clean?

e.

Does the test require the sample to be at a certain 
temperature?

f.

Was the pH of the sample in the correct range?

g.

Is the pipette volume correct?

2.

Check the reagents. Repeat the standard additions using 
fresh reagents.

If none of these measures resolves the problem, please contact 
the manufacturer.

5.4.10.1

Complete a standard addition

Carry out the standard addition in accordance with the 
corresponding procedure.

There are two different methods:

Maximum Volume (standard addition)

A defined volume of a standard solution of known concentration 
is incrementally added to a previously tested sample and the 
sample is newly measured after every standard addition.

Sample volume:

A defined volume of a standard solution of known concentration 
is added to the volume of sample specified in the procedure and 
the sample is measured after each addition. In most cases three 
different standard solutions are prepared and the procedure is 
repeated for each of them.

Note: The units and chemical forms used for the sample are used for the 
standard solutions. Be careful to make sure that to use the correct units 
for subsequent entries.

Detection rate

Conclusion

100%

The originally used reagents were defective. 

Check the standard solution: 

Repeat the standard addition procedure with 
a freshly prepared standard solution and 
distilled water!

Detection rate

Conclusion

100%

The originally used 
standard solution 
was deficient.

Содержание DR 6000





























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды