GST GST200-2 Скачать руководство пользователя страница 18

Страница: 18 / 60

GST200-2 Intelligent Fire Alarm Control Panel

Installation and Operation Manual

Page 15

Chapter 4 Installation

The steps below are guidance for installation of the FACP.

Check if you have received all items ordered.

Install the cabinet.

Power up the FACP and carry out start-up inspection.

Connect field devices.

Inspect circuits and register devices.

Define devices and C&E equations on a PC and download them to the FACP

through definition software according to engineering configuration.

Commission and inspect field devices.

4.1 Component Inspection

Before installation, check the following items:



Check Engineering Requirement

Check the components according to packing list. The main items to be examined are:

installation and operation manual, keys to the FACP, etc.



Check Internal Components and Interconnection of the FACP

All internal parts have been connected (including optional units ordered) before the

FACP leaves the factory. Therefore, you can mainly check the zone indication and

manual intervention panel and power supply, and the connection among parts, including

the connection between main board and power supply, switch board and loop interface

board, the connection of the zone indication and manual intervention panel with switch

board, and of speaker and main board etc. Please refer to Appendix 1 for the internal

connection diagram.

4.2 Installing the Cabinet

Dimension of the cabinet is shown in Fig. 4-1.

Ambient conditions for installation of the FACP:

Temperature: 0

℃

＋

℃

Relative humidity

≤

％

, non-condensing

Содержание GST200-2





























































Результаты поиска

Содержание GST200-2

Отзывы:

GST GST200-2, Инструкция по установке и эксплуатации, Страница: 18 / 60

Результаты поиска

Содержание GST200-2

Отзывы: