GST GST100 Скачать руководство пользователя страница 10

Страница: 10 / 48

GST100 Intelligent Fire Alarm Control Panel
Installation and Operation Manual

Page 6

OUTPUT

Green sounder (R+, R-) outputs.

②

Both LED illuminate when

SOUNDER OUTPUT (R+, R-) is
disabled.

③

Both LED flash when the

SOUNDER OUTPUT (R+, R-) is in
trouble condition.

panel is reset.

②

Both LED go off when the

SOUNDER OUTPUT (R+, R-)
is enabled.

③

Both LED go off when the

trouble condition is cleared.

Disabled

Yellow Turns on when there is a connected

device or an output or the delay
mode is disabled.

Enable all devices or outputs,
refer to Section 6.5

Fault

Yellow Turns on when a trouble condition is

detected.

Remove the cause of the
trouble.

AC Fault

Yellow Turns on when 230VAC power

supply is down or damaged.

Remove the cause of the
trouble.

Battery Fault

Yellow Turns on when the standby battery

is under-voltage or damaged.

Remove the cause of the
trouble.

System Fault Yellow

①

Illuminates when the memory of

the panel is in trouble.

②

Flashes when system program

cannot be executed.

Remove the cause of the
trouble.

Power
Healthy

Green Illuminates when power supply

works normally.

Maintenance

Yellow Illuminates when a detector reports

dirty.

Clean the detector and then
reset the panel.

Mute

Yellow Illuminates

when

the

panel

’s

speaker is turned off.

Verify the cause of the event
and reset the control panel.
Note: If there is new fire alarm,
the speaker will be re-activated
and this LED will go off.

Silence

Yellow Illuminates when the sounders are

silenced or when the SOUNDER
OUTPUT (R+, R-) is disabled.

Verify  the  cause  of  the  event
and reset the control panel.
Note:  If  there  is  new  fire  alarm
or  the

Silence

key is pressed

again,

the

sounder

SOUNDER OUTPUT will be
re-activated and this LED goes
off.

Delay

Yellow Illuminates when there is a sounder

or an output in delay mode.

Verify the cause of the event.
This LED goes off when the
panel is reset or the delay time
expires.

Zonal LED
Fire

Red

Turns on when a device of the zone
alarms fire.

Verify the cause of the event
and then reset the FACP.

Flt/Disabled

Yellow

①

Flashes if a device of the zone is

in trouble condition.

②

Illuminates if all devices of the

zone are disabled.

①

Remove the cause of the

trouble.

②

Enable all devices of the

zone.

Содержание GST100

















































Результаты поиска

Содержание GST100

Отзывы:

GST GST100, Инструкция по установке и эксплуатации, Страница: 10 / 48

Результаты поиска

Содержание GST100

Отзывы: