background image

Nr. 17.02 -i4

19 / 20

Tel. 0 72 61 -92 63-0

Telefax 0 72 61 -92 63-33

e-mail: [email protected]

Declaration of Incorporation

According to 2006/42/EC, Annex II, No. 1 B

Translation

Authorized person/ 

the manufacturer

 

[company or natural person]

GROB GmbH, Eberhard-Layher-Str. 5, 

74889 Sinsheim

Description and

identification of the

machinery:

Baureihe MC 

Technical specifications according to our

order confirmation to raise and lower loads.

The following

essential health and

safety requirements

according to Annex I

of this directive are

applicable and have

been fulfilled:

1.1.2

1.3.2

1.3.7

1.38

1.61

1.74

4.4.2

The following

harmonized

standards (or parts

therof) were applied:

EN ISO 12100-1 Safety of machinery - Basic 

concepts, general principles for design

EN 1570:1998 Safety requirements for lifting 

tables

EN 1495:1997 Lifting platforms - Mast 

climbing work platforms

EN 280:2001 Mobile elevating work platforms

The relevant technical documentation according to Annex VII B has 

been established and it shall be delivered electronically to the national 

authorities in charge upon request.

This partly completed machinery must not be put into service until the 

final machinery into which it is to be incorporated, has been declared in 

conformity with the provisions of the machinery directive.

Содержание MC Basic





















Отзывы: