Grizzly G0820 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 104

Grizzly G0820 Скачать руководство пользователя страница 78

-76-

Model G0820 (Mfd. Since 12/16)

Sliding Table Parallel

Adjustment

The sliding table is adjusted parallel with the
main blade at the factory, but it can re-adjusted if
necessary.

Tools Needed

Qty

Felt Tip Pen ....................................................... 1
90° Square ........................................................ 1
Precise Measuring Tool ..................................... 1
Wrench or Socket 17mm ................................... 1
Wrench or Socket 19mm ................................... 1

To adjust sliding table parallel with main

blade:

1. DISCONNECT MACHINE FROM POWER!

2. Raise main blade as high as it will go and

adjust tilt angle to 0° (verify with square).

3. Mark one blade tooth with felt tip pen. This

will be your reference point when taking mea-
surements in following steps.

4. Move sliding table all the way forward, and

measure distance “A” shown in

Figure 156,

which is between marked blade tooth and
edge of sliding table miter slot.

Figure 156. Measuring distance between miter

slot and blade at each end of sliding table.

Marked Tooth

B

Marked Tooth

Blade

Miter Slot

A

5. Rotate blade 180°, move sliding table all the

way back, then measure distance “B” shown
in

Figure 156.

— If “A” and “B” measurements are same

or difference is 0.004" or less, no adjust-
ments to table parallelism need be made.

— If difference is greater than 0.004", then

sliding table parallelism must be adjusted.
Proceed to

Step 6.

6. Loosen hex nuts on sliding table T-bolts to

allow sliding table to move in next step (refer
to

Figures 157–158), and loosen hex nuts on

each adjustment bolt

.

7. Turn adjustment bolt under each end of slid-

ing table to make sliding table parallel with
main blade.

8. Once sliding table parallelism is within 0.004"

from one end to the other, retighten hex nuts.

Figure 158. Rear parallelism adjustment bolt

and T-bolt.

T-Bolt

Adjustment Bolt

Figure 157. Front parallelism adjustment bolt

and T-bolt.

T-Bolt

Adjustment Bolt

«
...
76
77
78
79
80
...
»

Содержание G0820









































































































Отзывы:

Нет отзывов