Grizzly G0820 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 104

Grizzly G0820 Скачать руководство пользователя страница 64

5"

5"

4" Slot

(Top View)

(Side View)

3

/

8

"

Countersink on Bottom

1

/

4

" Hole

Figure 127. Miter bar pattern.

5. Cut miter bar that will fit in table miter

slot approximately 5" long, as shown in

Figure 127.

Tip: Consider making the miter bar longer for
larger featherboards—approximately half the
length of the total featherboard—to support
the force applied to the featherboard during
use.

7. Mark 4" line through center of countersunk

hole in center, then use jig saw with narrow
blade to cut it out.

8. Assemble miter bar and featherboard with

1

⁄

4

"-20 x flat head screw, flat washer, and a

wing nut or a star knob (see

Figure 128).

Congratulations! Your featherboard is com-
plete.

4. Rout

1

⁄

4

"–

3

⁄

8

" wide slot 4"–5" long in workpiece

and 1"–2" from short end of featherboard
(see

Figure 126).

Figure 126. Slot routed in featherboard.

1"-2"

4"-5"

1

/

4

"-

3

/

8

"

Slot

(Side View)

Wing Nut

Miter Bar

Featherboard

Flat Head Screw

Flat Washer

Figure 128. Assembling miter slot featherboard

components.

Note: The routed slot, countersink hole, and
the flat head screw are essential for the miter
bar to clamp into the miter slot. When the
wing nut is tightened, it will draw the flat head
screw upward into the countersunk hole. This
will spread the sides of the miter bar and
force them into the walls of the miter slot,
locking the featherboard in place.

Tip: The length of the flat head screw depends

on the thickness of the featherboard—though
1

1

⁄

2

" to 2" lengths usually work.

Now, proceed to

Mounting Featherboard in

Miter Slot on Page 63.

6. Drill

1

⁄

4

" hole in center of bar, then countersink

bottom to fit

1

⁄

4

"-20 flat head screw.

-62-

Model G0820 (Mfd. Since 12/16)

«
...
62
63
64
65
66
...
»

Содержание G0820









































































































Отзывы:

Нет отзывов