Grizzly G0820 Скачать руководство пользователя страница 60

Страница: 60 / 104

-58-

Model G0820 (Mfd. Since 12/16)

Commonly used in furniture joinery, a rabbet is an

L-shaped groove cut in the edge of the workpiece.

Typically, rabbets can be cut with either a dado

blade or a standard saw blade. However, because
the Model G0820 cannot accept dado blades, rab-
bets must be cut with a standard saw blade only.

A ripping blade is typically the best blade to use
for cutting rabbets when using a standard blade
because it removes sawdust very efficiently. (See

Page 44 for blade details.) Also, a sacrificial fence
is not required when cutting rabbets with a stan-
dard blade.

Rabbet Cutting

Workpiece

Fence

Blade

Figure 122. Second cut to create a rabbet.

5. Reconnect saw to power source, then per-

form cut.

6. Lay workpiece flat on table, as shown in

Figure 122, adjust saw blade height to inter-
sect with first cut, then perform second cut to
complete rabbet.

Always use push sticks, featherboards,

push paddles, and other safety accessories

whenever possible to increase safety and

control during operations which require

removal of blade guard. ALWAYS replace

blade guard after operation is complete.

3. Raise blade to desired depth of rabbet chan-

nel desired.

Fence

Blade

Workpiece

Figure 121. First rabbet cut.

4. Stand workpiece on edge, as shown in

Figure 121, then adjust rip fence so blade is
aligned with inside of rabbet channel.

DO NOT place a tall board on edge when

cutting a rabbet. Overly tall workpieces can-

not be properly supported with the fence

and can easily shift during operation, caus-

ing kickback or loss of control. Instead, use

another tool to cut these types of rabbets.

To cut rabbets with standard blade:

1. DISCONNECT MACHINE FROM POWER!

2. Mark width of rabbet cut on workpiece.

Include marks on edge of workpiece so cut
path can be aligned when workpiece is lying
on table.

Содержание G0820









































































































Результаты поиска

Содержание G0820

Отзывы:

Grizzly G0820, Руководство пользователя, Страница: 60 / 104

Результаты поиска

Содержание G0820

Отзывы: