Grizzly G0820 Скачать руководство пользователя страница 31

Страница: 31 / 104

Model G0820 (Mfd. Since 12/16)

-29-

33. Slide rip fence stop ring onto left end of rail

and tighten pre-installed set screw to secure
it in place (see

Figure 39). When installed

correctly, this ring will prevent rip fence from
contacting blade.

30. Use straightedge to make sure riving knife

r splitter/riving knife and sco

ring blade are

aligned with main blade, as shown in

Figure

37. The alignment should be with blade bod-
ies, not carbide teeth (see inset).

— The

riving knife or splitter/riving knife

position can be changed by adjusting set
screws at splitter/riving knife mounting
block. Refer to

Riving Knife Mounting

Block on Page 78 for more details.

— The scoring blade alignment can be

changed by adjusting

bolt

accessible

through table top (see

Figure 37). Refer

Aligning to Scoring Blade on Page 48

for more details.

Figure 37. Access holes for scoring blade

adjustment controls.

31. Close blade cover. Center sliding table over

cabinet body and lock in place with sliding
table lock lever (see

Figure 38).

34. Attach rip fence end stop on opposite end of

rip fence rail with (1) M8-1.25 x 15 cap screw
and (1) 8mm lock washer (see

Figure 40).

Figure 40. Rip fence end stop attached to rail.

Rip Fence

End Stop

Figure 39. Rip fence stop ring attached to rail.

Rip Fence

Stop Ring

x 1

35. Adjust rip fence to main blade and tables,

as instructed in

Calibrating Rip Fence on

Page 79.

Scoring Blade Elevation

Scoring Blade Alignment

Figure 38. Location of sliding table lock lever.

32. Position rip fence

⁄

" away from main blade.

Sliding Table

Lock Lever

Содержание G0820









































































































Результаты поиска

Содержание G0820

Отзывы:

Grizzly G0820, Руководство пользователя, Страница: 31 / 104

Результаты поиска

Содержание G0820

Отзывы: